Search found 61 matches

by DJ-Bino
Sat Sep 26, 2020 10:41 pm
Forum: VCarve - General
Topic: Thread Milling - I can't get it working
Replies: 11
Views: 323

Re: Thread Milling - I can't get it working

Hello Frank, Can it be that you cut a left-hand thread instead of a right-hand thread. I have no problems with the tool parameters and settings. Hallo Frank, Kann es sein das du ein Linksgewinde schneidest anstatt eines Rechtsgewinde. Ich habe mit den Werkzeugparameter und Einstellungen keine Probl...
by DJ-Bino
Sat Sep 26, 2020 12:02 am
Forum: VCarve - General
Topic: Thread Milling - I can't get it working
Replies: 11
Views: 323

Re: Thread Milling - I can't get it working

Hallo Frank, du musst den Gewindedurchmesser auswählen, nicht den vom Kernloch. Deinen Gewindedurchmesser musst du auch mit einem 8mm Durchmesser zeichnen. Den markierst du dann und wählst aus der Liste M8 aus. Nun kannst du dir auch noch den Kreis für den Kerndurchmesser des Innengewinde automatisc...
by DJ-Bino
Fri Sep 25, 2020 6:03 pm
Forum: VCarve - General
Topic: Thread Milling - I can't get it working
Replies: 11
Views: 323

Re: Thread Milling - I can't get it working

Hello Frank,
that's strange. Maybe you can use your file
upload to see if everything is ok.
Hallo Frank,

das ist seltsam. Vielleicht kannst du ja mal deine Datei
hier hoch laden um zu sehen ob da alles in Ordnung ist.

Gruß Dieter
by DJ-Bino
Fri Sep 25, 2020 11:34 am
Forum: VCarve - General
Topic: Thread Milling - I can't get it working
Replies: 11
Views: 323

Re: Thread Milling - I can't get it working

Hi Frank, verwende mal folgende Werte für deinen Gewindefräser. Der Sorotec und Datron funktionieren beide damit. Die Zahnbreite (S) wird so berechnet D1-D2 /2 Die Zahnhöhe(H) wird automatisch berechnet sobald du die Zahnbreite eingetragen hast. Du kannst auch die Zahnhöhe(H) nach folgender Formel s...
by DJ-Bino
Fri Sep 11, 2020 10:53 pm
Forum: VCarve - General
Topic: CAN'T INPUT A THREAD LENGTH
Replies: 6
Views: 197

Re: CAN'T INPUT A THREAD LENGTH

Why can I not input a thread length? It stays grayed out. THREAD CUTTING.JPG Hello, when I look at your picture I immediately notice that you specify a maximum depth of 3 ". But entered 8 "at pitch below. I think that was not a good idea. :) If you use real values then the thread length will be dis...
by DJ-Bino
Tue Sep 01, 2020 11:08 am
Forum: Aspire - Tips and Tricks
Topic: Add Aspire to Windows "New" Menu
Replies: 1
Views: 208

Re: Add Aspire to Windows "New" Menu

Hello,

The tip works 100% for me with Windows7
Thanks a lot for this.
by DJ-Bino
Fri Jul 24, 2020 9:58 pm
Forum: Aspire - General
Topic: More Nodes
Replies: 24
Views: 918

Re: More Nodes

Hi Michael,

I think you are alone at home for too long. :mrgreen:
This is not good. :lol:

Your CNC machine is happy with as few knots as necessary.

The more knots, the more often the machine has to accelerate and brake.

This then leads to jerking.

Dieter
by DJ-Bino
Fri Jul 24, 2020 11:06 am
Forum: Post Processors
Topic: PostProcessor Problem
Replies: 4
Views: 380

Re: PostProcessor Problem

Hi Adrian,

I knew it was working. I just had to rename it. Both the name and the variable POST_NAME =

Otherwise nothing had to be changed.

Thanks Dieter
by DJ-Bino
Thu Jul 23, 2020 10:25 am
Forum: Post Processors
Topic: PostProcessor Problem
Replies: 4
Views: 380

Re: PostProcessor Problem

Make sure to send this into support@vectric.com Hi Randall, It is a PP from a customer. Mohamed already knows. It is a customized PP that also works if you rename it. It has an ä in the name and also for the variable POST_NAME = is an ä in the name. This worked well until version 10.22 From version...
by DJ-Bino
Sat Jul 18, 2020 9:56 am
Forum: Post Processors
Topic: PostProcessor Problem
Replies: 4
Views: 380

PostProcessor Problem

Hello everybody, I found another bug that prevented the postprocessor from reading. In version 10 it is possible to load post processors with ä, ü, ö in the name. In version 10.5xx, the postprocessor name cannot contain ä, ö, ü Also with the parameter POST_NAME = these characters may not be used Die...
by DJ-Bino
Fri Jul 10, 2020 11:49 pm
Forum: Aspire - General
Topic: I think that I have a problem with the new chamfering tool
Replies: 7
Views: 304

Re: I think that I have a problem with the new chamfering tool

Hi,
The Moulding Toolpath creates a 3D toolpath
The chamfertolpath is only 2D

The Moulding Toolpath would be the better choice for your application

Dieter
by DJ-Bino
Fri Jul 10, 2020 11:05 pm
Forum: Aspire - General
Topic: I think that I have a problem with the new chamfering tool
Replies: 7
Views: 304

Re: I think that I have a problem with the new chamfering tool

hi alfredom, as already correctly described by Steve your values are not correct. Remember you are now working with the tool on a steep wall I get along best with these settings. See attached pictures If this is still too rough for you, you can reduce the value from 14% to 7%. It will only take long...
by DJ-Bino
Wed Jul 08, 2020 5:41 pm
Forum: Aspire - General
Topic: 3D graphics card performance expectations with Aspire
Replies: 9
Views: 323

Re: 3D graphics card performance expectations with Aspire

Hi Stephen, Your problem could be that your AMD graphics card does not support DirectX. Compare yours with this one. https://www.amd.com/en/products/professional-graphics/radeon-pro-wx-7100-mobile You do not have the software API Support I always recommend using an Nvidia graphics card for CAD / CAM...
by DJ-Bino
Thu Jun 25, 2020 10:49 pm
Forum: Aspire - General
Topic: 10.5 is COMING SOON - Watch this space
Replies: 88
Views: 10140

Re: 10.5 is COMING SOON - Watch this space

Macs are only 10% of personal computer users. How is that going to get better when everyone runs after Microsoft like the lemmings? The collection of user data cannot be stopped in this way. Would there be more manufacturers who would program across platforms. Would stop dependency on Microsoft. I'...
by DJ-Bino
Wed Jun 24, 2020 8:39 pm
Forum: Aspire - General
Topic: 10.5 is COMING SOON - Watch this space
Replies: 88
Views: 10140

Re: 10.5 is COMING SOON - Watch this space

I didn't upgrade to 10, but if you amaze me with what you add to 10.5 you might be able to crack open my stingy wallet. I'm hoping for something close to automatic spell check, except it would be automatic vector check. I make a mistake, and it offers up a few suggestions that guess what I meant to...