I finally found it. Thanks for hanging with me. What is the V9 3D tabs clipart for Vcave on your list? I have the 3D tabs but not that one.
Thanks again
Search found 20 matches
- Thu Oct 26, 2017 5:05 am
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
- Wed Oct 25, 2017 11:13 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
Re: 3D boundary offsets
I logged in at this address https://portal.vectric.com/account and it gives me a welcome to V & CO. I don't see any clip art installers. I don't remember this page.
Thanks
Thanks
- Wed Oct 25, 2017 10:14 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
Re: 3D boundary offsets
Help again please. I logged into the vectric portal and I don't see where to download the 3D tabs. Also, where can I find the clip art I downloaded?
Thanks again
Thanks again
- Wed Oct 25, 2017 5:05 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
Re: 3D boundary offsets
Great. Thanks again.
- Tue Oct 24, 2017 9:07 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
Re: 3D boundary offsets
I appreciate the info. I'm not sure what you mean by adding the 3D tabs. Are you talking about adding them at a profile cutout in 2D? Wouldn't the ball nose take them out too?
- Tue Oct 24, 2017 7:54 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
Re: 3D boundary offsets
That's what I thought but if I set boundary offset to .25 (using a .25 end mill and a .25 ball nose) it cuts through my material on the outside parameter during the finish cut. It shows that on the previews also. Am I missing something?
Thanks
Thanks
- Tue Oct 24, 2017 7:08 pm
- Forum: Design & Make Clipart- General
- Topic: 3D boundary offsets
- Replies: 12
- Views: 10035
3D boundary offsets
When using the Vectric clip art with Vcarve pro, how do I determine the cut depth on the parameter? I noticed on the 3D roughing and the 3D finishing tool paths, there are boundary offsets. When I set these to .15 it came close to cutting through but gave me a nicer edge. Although, anything greater ...
- Thu Jan 12, 2017 10:27 pm
- Forum: VCarve - General
- Topic: Feed and speed for 1 !/2" bit
- Replies: 4
- Views: 4791
Re: Feed and speed for 1 !/2" bit
Thanks for the info.
- Wed Jan 11, 2017 7:22 pm
- Forum: VCarve - General
- Topic: Feed and speed for 1 !/2" bit
- Replies: 4
- Views: 4791
Feed and speed for 1 !/2" bit
I am looking for speed and feed rate, stepover and plunge rate advice for Amana 1 1/2" #45566 carbide tipped bottom cleaning/spoilboard bit. I am using it to flycut mdf spoil boards. Also, I plan to use it on soft and hardwoods. Not sure if the rates would change. I am running a Laguna IQ.
Thanks
Thanks
- Fri Dec 09, 2016 10:42 pm
- Forum: VCarve - General
- Topic: X + out of soft limit
- Replies: 3
- Views: 3378
Re: X + out of soft limit
Thanks. The largest it would let me make the width was 23.25
- Fri Dec 09, 2016 9:00 pm
- Forum: VCarve - General
- Topic: X + out of soft limit
- Replies: 3
- Views: 3378
X + out of soft limit
I am trying to flycut a spoilboard on a Laguna IQ w/ V Carve Pro. I set up a pocket cut @.01 and 24 x 24 but my HHC gives me a X + out of soft limit. Is there a way around this so I can machine the entire board? I am using a 1/2" end mill until my 1 1/2 " gets here.
Thanks
Thanks
- Mon Sep 12, 2016 2:03 am
- Forum: VCarve - General
- Topic: Sea turtle 3D Clipart
- Replies: 6
- Views: 3771
Re: Sea turtle 3D Clipart
This worked out great. Thank you.
- Fri Sep 09, 2016 2:37 pm
- Forum: VCarve - General
- Topic: Sea turtle 3D Clipart
- Replies: 6
- Views: 3771
Re: Sea turtle 3D Clipart
Thanks again. Is it possible to resize these using V Carve Pro?
- Fri Sep 09, 2016 3:52 am
- Forum: VCarve - General
- Topic: Sea turtle 3D Clipart
- Replies: 6
- Views: 3771
Re: Sea turtle 3D Clipart
Thank you. These will work with V Carve Pro?
- Thu Sep 08, 2016 7:25 pm
- Forum: VCarve - General
- Topic: Sea turtle 3D Clipart
- Replies: 6
- Views: 3771
Sea turtle 3D Clipart
I am looking for some sea turtle 3D clipart for V-Carve Pro.
Thanks in advance.
Thanks in advance.