Search found 285 matches
- Wed Mar 27, 2024 1:44 pm
- Forum: Aspire - Gallery
- Topic: Demon-Proof Box
- Replies: 5
- Views: 384
- Tue Mar 19, 2024 2:48 pm
- Forum: Aspire - Tips and Tricks
- Topic: Any AI masterpieces ?
- Replies: 32
- Views: 3893
Re: Any AI masterpieces ?
+1 (impressive). thanks.
- Mon Mar 11, 2024 4:36 pm
- Forum: Hardware related questions
- Topic: Big Changes Coming
- Replies: 5
- Views: 993
Re: Big Changes Coming
Thanks for posting your journal of your journey so i can watch...
- Mon Mar 04, 2024 12:01 pm
- Forum: Aspire - General
- Topic: Importing an STL
- Replies: 8
- Views: 585
Re: Importing an STL
+1 thanks to Rcnewcomb re pointer to milo scott narrative.
- Mon Mar 04, 2024 11:50 am
- Forum: Aspire - General
- Topic: Couple videos of furniture parts cut with Aspire
- Replies: 13
- Views: 717
Re: Couple videos of furniture parts cut with Aspire
+1 thanks for the video
- Tue Feb 27, 2024 9:21 pm
- Forum: Aspire - Tips and Tricks
- Topic: Any AI masterpieces ?
- Replies: 32
- Views: 3893
Re: Any AI masterpieces ?
+1 (and hat tip re rainbow scratch paper)
- Fri Feb 23, 2024 3:10 pm
- Forum: VCarve - Gallery
- Topic: Pocket Epoxy VCarve Desktop
- Replies: 9
- Views: 619
Re: Pocket Epoxy VCarve Desktop
Clever too.
- Tue Feb 13, 2024 8:53 pm
- Forum: Aspire - General
- Topic: Do these AI gadgets have humor?
- Replies: 11
- Views: 1049
Re: Do these AI gadgets have humor?
Perplexity and Phind also similar results from Aria.
- Thu Feb 08, 2024 6:50 pm
- Forum: Control Software related questions
- Topic: Changing over to a UC400ETH, Advice Appreciated
- Replies: 5
- Views: 988
Re: Changing over to a UC400ETH, Advice Appreciated
swell. luck with the clean up.
- Thu Feb 08, 2024 6:48 pm
- Forum: Wrapped Rotary Machining
- Topic: Modelling question
- Replies: 9
- Views: 949
Re: Modelling question
I suppose if each of the 4 sides are the same (or in pairs), then take your 4-sided stock and 2-d cut each side (manually turning/flipping 90 degrees following each cut); perhaps?
- Thu Feb 08, 2024 6:45 pm
- Forum: Aspire - Gallery
- Topic: Medieval Themed Master Bedroom
- Replies: 13
- Views: 1197
- Fri Feb 02, 2024 1:53 pm
- Forum: Control Software related questions
- Topic: Changing over to a UC400ETH, Advice Appreciated
- Replies: 5
- Views: 988
Re: Changing over to a UC400ETH, Advice Appreciated
a little longer before i go to the UC400ETH (similar setup and age of equipment) -- in the meanwhile, was curious also about using a microscope
- Thu Feb 01, 2024 12:46 pm
- Forum: Aspire - Gallery
- Topic: Inlay on a curved surface
- Replies: 21
- Views: 2771
Re: Inlay on a curved surface
And also thanks to ZipperHead55
- Thu Feb 01, 2024 12:41 pm
- Forum: Gadgets - General
- Topic: Dovetail drawers
- Replies: 28
- Views: 2600
Re: Dovetail drawers
Nifty (as usual).
- Wed Jan 31, 2024 11:37 am
- Forum: Aspire - Gallery
- Topic: 7.5 foot tall flying eagle
- Replies: 11
- Views: 1340
Re: 7.5 foot tall flying eagle
words are not good enough.