Search found 4364 matches
- Mon Apr 22, 2024 10:38 pm
- Forum: Cut3D - General
- Topic: Version 12 Modeling issue
- Replies: 2
- Views: 55
Re: Version 12 Modeling issue
Remember that 3D finishing toolpaths stop when the centre of the bit reaches the selected vector boundary + boundary offset. You have a boundary offset of 0 so the bit will not travel deeper than you see. If you make that boundary offset 0..24 you will get the effect you are looking for with the mod...
- Mon Apr 22, 2024 8:14 pm
- Forum: VCarve - General
- Topic: 3d Question
- Replies: 2
- Views: 60
Re: 3d Question
On the "Design" tab is a section (below Offset and Layout) labelled 3D Model Tools.
Presumably it was moved there so that you don't have to click on the Component Tab then click on the icon in question.
As for the state of your vision only you and your ophthalmologist can answer that.
Presumably it was moved there so that you don't have to click on the Component Tab then click on the icon in question.
As for the state of your vision only you and your ophthalmologist can answer that.
- Mon Apr 22, 2024 6:54 pm
- Forum: Aspire - General
- Topic: curve tool
- Replies: 8
- Views: 327
Re: curve tool
Bring back draw curve tool. Please. I disagree. That tool rarely produced useful curves that didn't need extensive editing due to the program trying to interpolate between your chosen end points. The changes to the "Draw Line" tool that Vectric made in v11.?? make it behave much like the "Pen" tool...
- Mon Apr 22, 2024 5:41 pm
- Forum: VCarve - General
- Topic: 3d files
- Replies: 2
- Views: 121
Re: 3d files
Define old? When I see a early 1980s Chrysler "K" car with collectors' plate on it I question what a really old vehicle is... You could go directly to "Thingiverse" If you just a broad search for STL files you'll probably get some suspect 3D model sites that merely wrap a Thingiverse link with their...
- Sun Apr 21, 2024 3:34 pm
- Forum: VCarve - General
- Topic: V12 Array Preview Broken
- Replies: 4
- Views: 203
Re: V12 Array Preview Broken
People really do need to stop using terms like "broken" and "bug" in their post titles. How about "V12 Array Copy Toolpath possible problem" or "Array Copy Toolpath (v12): I'm seeing a strange behaviour"... Is the "Toggle toolpath 3D drawing visible" option (3rd icon in the upper left corner of the ...
- Fri Apr 19, 2024 5:31 pm
- Forum: VCarve - Tips and Tricks
- Topic: Bottoming out a collet nut
- Replies: 32
- Views: 4492
Re: Bottoming out a collet nut
That information plus a good 6 inch (15cm) rule to measure the amount of the bit sticking out of the collet goes a long way to avoiding crashes. :D Thanks, Martin, for reminding me that this information exists. I keep forgetting to slow down and hover there and plenty other places in the software......
- Thu Apr 18, 2024 9:10 pm
- Forum: Aspire - General
- Topic: Off line computers
- Replies: 6
- Views: 190
- Thu Apr 18, 2024 7:12 pm
- Forum: VCarve - General
- Topic: Help with Roundover bit following edge of a chair seat
- Replies: 9
- Views: 261
Re: Help with Roundover bit following edge of a chair seat
Because of the horn in the centre of the seat you'll probably also need two overlapping fluting paths.
- Thu Apr 18, 2024 5:12 pm
- Forum: VCarve - General
- Topic: Version 12 Tool/Feature Name Changes (Be-Fuddling)
- Replies: 15
- Views: 699
Re: Version 12 Tool/Feature Name Changes (Be-Fuddling)
Everything seems to be a tad bit smaller. Do grade 9 writing teachers still warn against "everything", "all", "everyone knows"? Mine did. Of course, "most things", "it seems that" to me always (oops!) seem to be affected. Both programs on a Windows box set to 100% scale (i.e. no scaling). 9_5 vs ...
- Thu Apr 18, 2024 5:04 pm
- Forum: Aspire - General
- Topic: V12 3D View - Model displays as transparent
- Replies: 11
- Views: 532
Re: V12 3D VIEW - Model displays as transparent
We might need an image. The dome below looks quite not transparent: no transparent.png Windows has a built-in snipping tool for taking screenshots and saving the image to a file. You can even draw highlights and annotations. The saved image file (png or jpg) can be uploaded as an attachment here...
- Thu Apr 18, 2024 4:57 pm
- Forum: Aspire - General
- Topic: 3D view center point
- Replies: 4
- Views: 163
Re: 3D view center point
I think I know what you have a problem with but it took poking around in the software and not reading anything here. Previous versions of Aspire / VCarve never had the ability to display the 2D vectors on the 3D view. Now it does. And software, being not very bright despite people slinging the terms...
- Thu Apr 18, 2024 3:34 pm
- Forum: VCarve - General
- Topic: Tool Database Ver. 11.5 to 12
- Replies: 10
- Views: 271
Re: Tool Database Ver. 11.5 to 12
And a picture of the exact tool (material and machine) from 11.5?
- Thu Apr 18, 2024 3:51 am
- Forum: Aspire - General
- Topic: Trial version tutorial sample files
- Replies: 2
- Views: 142
Re: Trial version tutorial sample files
All will be revealed in the Help menu. There should be an entry for "Tutorials" that will go to the local (your computer) repository for the tutorials.
- Thu Apr 18, 2024 12:06 am
- Forum: Aspire - Tips and Tricks
- Topic: Fun Topic: Artificial Intelligence (AI) Syntax
- Replies: 3
- Views: 298
Re: Fun Topic: Artificial Intelligence (AI) Syntax
Perhaps an example of what you consider bad syntax to be would help us?
- Wed Apr 17, 2024 2:53 pm
- Forum: Hardware related questions
- Topic: All my profile projects are not cutting through the wood.
- Replies: 5
- Views: 518
Re: All my profile projects are not cutting through the wood.
Up until now it's worked great. Thanks Considering the rest of your post this is a bit of a contradiction. The question I would have to ask is what did you do between when it "worked great" and now that "No matter what I do, the drill bit does not cut through the wood"? Did you upgrade from an earl...