Search found 379 matches

by Tailmaker
Fri Jul 30, 2021 6:08 pm
Forum: Aspire - Gallery
Topic: Another Staved Project
Replies: 8
Views: 224

Re: Another Staved Project

.....CA'ing all those staves would just about do me in.... Not that bad. I first stuck the staves to 2 strips of duct tape, wrapped it up and tightened around the lids and in the middle with several hose clamps. Then removed the tape and tacked the gaps between the staves with medium CA glue, just ...
by Tailmaker
Fri Jul 30, 2021 4:47 am
Forum: Aspire - Gallery
Topic: Another Staved Project
Replies: 8
Views: 224

Re: Another Staved Project

Continued...

The hardened epoxy is again sanded smooth up to 1000 grit and buffed with steel wool and polish paste.
BuffedFinish.JPG
So this is the final result. Looks good to me...
Can not be used for flowers that need water but rather for dry flower arrangements.
CompletedVase.JPG
by Tailmaker
Fri Jul 30, 2021 4:44 am
Forum: Aspire - Gallery
Topic: Another Staved Project
Replies: 8
Views: 224

Re: Another Staved Project

Continued.... With some trouble I got the 21 staves assembled and tacked together with CA glue: AssembledAndTacked.JPG The program also calculates the proper diameter and chamfer angles for lids on both sides: ChamferedLid.JPG The assembly is sanded smooth on the lathe: SandedAssy.JPG Final strength...
by Tailmaker
Fri Jul 30, 2021 4:38 am
Forum: Aspire - Gallery
Topic: Another Staved Project
Replies: 8
Views: 224

Another Staved Project

Some 2 years ago I wanted to make barrels and similar shaped things using staves and wrote a program to calculate the .stl of such staves (before bending) based on e.g. top, middle and bottom diameter, height, wall thickness etc. I ended up making a mini-conga and posted the result on this forum. No...
by Tailmaker
Wed Jul 21, 2021 12:38 am
Forum: Gadgets - General
Topic: Gear Maker-Be aware of these limitations:
Replies: 4
Views: 239

Re: Gear Maker-Be aware of these limitations:

Good point. I have another method: - move the gear center to x0/y0 - tweak one tooth/one notch in node editing mode as desired (I usually extend the notch bottom round) - cut the vector at the beginning/end of this tooth/notch segment and delete the vector with the unmodified teeth - rotate/copy the...
by Tailmaker
Fri Jul 09, 2021 6:50 pm
Forum: VCarve - General
Topic: Cut multiple node intersections at once
Replies: 4
Views: 221

Re: Cut multiple node intersections at once

The theory being that you'll get the pockets you want separated by very small space as the bitmap to vector function traces on "both sides of a line". Wouldn't an offset inward accomplish the same thing? Theoretically an offset in both direction should do the job. Unfortunately Aspire seems to get ...
by Tailmaker
Wed Jun 30, 2021 12:50 am
Forum: Aspire - Gallery
Topic: More Koru Fibonacci
Replies: 3
Views: 349

Re: More Koru Fibonacci

I see what you did and the result looks great. Question for me is why not cut it from one piece? Was it material saving or machine size?
by Tailmaker
Thu Jun 10, 2021 9:52 pm
Forum: Hardware related questions
Topic: Chisels
Replies: 16
Views: 983

Re: Chisels

........But yea, I agree, picking up a top quality tool and using it is very satisfying........ I my case it was rather buying a set of quality tools (the Narex bench and mortise chisels sets) with the optimistic intent of making more handcrafted items. However as it turns out I usually take to chi...
by Tailmaker
Sun May 30, 2021 11:35 pm
Forum: Aspire - Tips and Tricks
Topic: Laser Etching Tile
Replies: 5
Views: 1494

Re: Laser Etching Tile

Tabletop epoxy pour might look good and needs only a single coat.
by Tailmaker
Sun Apr 18, 2021 7:24 pm
Forum: VCarve - General
Topic: 2 part ? reducing drill deflection and engraver chatter
Replies: 3
Views: 307

Re: 2 part ? reducing drill deflection and engraver chatter

You could try something like that: https://www.ebay.com/itm/5-1-8-CARBIDE-END-MILL-3-FLUTE-45-DEG-POLISHED-FOR-ALUMINUM-YG1-28558-5-pack/383886863211 But I have used whatever cheap eBay 1/8" carbide upcut bit I had available. IIRC the fishtail ends worked better than the bottom cutting ones but did ...
by Tailmaker
Sun Apr 18, 2021 3:57 pm
Forum: VCarve - General
Topic: 2 part ? reducing drill deflection and engraver chatter
Replies: 3
Views: 307

Re: 2 part ? reducing drill deflection and engraver chatter

The anodizing layer is aluminum oxide (aka sapphire) and very hard. A drill bit with a tip tends to wander around until there is enough pressure to break the thin layer (you may notice the powdery substance). Not sure if that can be totally avoided, especially if the bit is long or the machine not v...
by Tailmaker
Sat Apr 17, 2021 1:40 am
Forum: VCarve - Gallery
Topic: Glass/Jar/Shaker Holder
Replies: 3
Views: 620

Glass/Jar/Shaker Holder

Another one of my simple utilitarian projects. The problem to solve was keeping the most used implements on the table of our 5th wheel trailer while traveling. Kind of annoying to rummage through various drawers and cabinets just to fetch the salt, sugar, maple syrup etc every time you stop. Obvious...
by Tailmaker
Thu Apr 01, 2021 2:09 pm
Forum: VCarve - General
Topic: Decimal Precision
Replies: 16
Views: 1127

Re: Decimal Precision

Not directly answering your software question, but I used a flatback tape measure for my miter saw: https://www.amazon.com/FastCap-PMS-FLAT-16-Flatback-Tape-Measure/dp/B005O3AWZG.

Has inches and mm and is not too expensive to cut up. I attached it with double sided adhesive tape.
by Tailmaker
Wed Mar 24, 2021 2:21 am
Forum: VCarve - General
Topic: Pocket and inlay issue.
Replies: 7
Views: 1113

Re: Pocket and inlay issue.

This may be they reason, how much is the diameter error?
If it is, you could choose "conventional" milling direction. This will usually pull the bit (and the machine) to make pocket bigger and inserts smaller. If you do that already, there is probably another reason.
by Tailmaker
Fri Mar 19, 2021 1:13 am
Forum: Wrapped Rotary Machining
Topic: 4th Axis Incomplete Finish Cut
Replies: 27
Views: 3548

Re: 4th Axis Incomplete Finish Cut

Not sure what PP you are using but on my machine the "regular" G94 post processor (feedrate=distance/min) does not work well when cutting mostly rotation moves because the machine interpretes that as feedrate=degrees/min. If I am lucky it works but often the axis stalls because the commanded angular...