Nice work guys, thank you. Hope you all have a good Christmas
Chuck
Search found 916 matches
- Tue Dec 08, 2009 10:14 am
- Forum: Aspire - General
- Topic: Aspire V2.5 Released
- Replies: 91
- Views: 62212
- Tue Dec 30, 2008 11:38 am
- Forum: PhotoVCarve - General
- Topic: What am i doing wrong?
- Replies: 9
- Views: 5270
Re: What am i doing wrong?
I am using Oak. I am cutting it with a 60 degree engraving bit. I am putting 2 coats of Shellac on the surface. I am programming the line spacing at 130% The depth is .048 The angle is 35. I cut the picture Then i put a dark stain all over the picture and then wipe it off the top. My carvings are a...
- Tue Dec 23, 2008 11:08 pm
- Forum: Aspire - General
- Topic: Hey Every one Happy Holidays!
- Replies: 10
- Views: 5129
Re: Hey Every one Happy Holidays!
Merry Christmas everyone. It has been a pleasure being part of the Vectric family.
Chuck
Chuck
- Sun Dec 21, 2008 11:41 am
- Forum: Cut3D - General
- Topic: Newbie Confuused on definition
- Replies: 8
- Views: 4556
Re: Newbie Confuused on definition
Tom you can rough it in with the 1/4 and finish with the 1/8th with a small stepover. 1/4 may not be enough depth to get the most out of what is possible
- Sun Dec 21, 2008 11:37 am
- Forum: VCarve - Gallery
- Topic: Candle holder, Thank you Khalid
- Replies: 8
- Views: 5363
Re: Candle holder, Thank you Khalid
Nice work guys, very creative
- Sun Dec 21, 2008 11:35 am
- Forum: VCarve - General
- Topic: need come creative design help
- Replies: 1
- Views: 1547
Re: need come creative design help
Will this work?
- Sun Dec 21, 2008 11:28 am
- Forum: Aspire - Tips and Tricks
- Topic: Roman Horses
- Replies: 12
- Views: 8292
Re: Roman Horses
Mark to change the height of the uppermost horse without affecting the others would require that horse to be seperated from the model. Tracing and cookie cutting might be your only option
- Sun Dec 21, 2008 11:22 am
- Forum: Aspire - General
- Topic: Need help please
- Replies: 3
- Views: 2682
Re: Need help please
You can make a circle around the center component (the bitmap) and make a planer shape from it with a height greater then what you currently have, that will raise it up. Make sure you place it at the top of the list in the Component manager.
- Sun Dec 21, 2008 11:06 am
- Forum: Aspire - General
- Topic: New to Aspire
- Replies: 6
- Views: 4090
Re: New to Aspire
Anthony, in the same run just make a text box and add your text the same has VCP. when you get ready to Vcarve or profile the text, click the box "Project toolpath onto 3d model" Make sure you have a safe Z when you run the job.
- Sun Dec 14, 2008 4:58 pm
- Forum: Aspire - General
- Topic: adding fonts
- Replies: 9
- Views: 5412
Re: adding fonts
Still can't get it to work. When VCarve or Aspire is first installed it "installs" fonts that are on the computer. Is there a way to do this step again without reinstalling? I'd appreciate some input from Tony or Brian. Aspire access's the TTf folder everytime it starts. Any changes (added or delea...
- Sun Dec 14, 2008 4:41 pm
- Forum: PhotoVCarve - General
- Topic: Bit question
- Replies: 9
- Views: 5699
Re: Bit question
Hi Crocky You mentioned an editor called Emeditor. Where can I get the software. Also, when I finish the carvings in wood do I need to apply stain to make the image visible as I cannot make out the image after carving. Ed Ed there are many different variations on finishing. Most I believe would use...
- Sun Dec 14, 2008 12:17 pm
- Forum: Aspire - General
- Topic: adding fonts
- Replies: 9
- Views: 5412
Re: adding fonts
I've done this before but for some reason I can't add fonts. I put the desired TTF font in the font folder for Aspire and then start the program. My understanding is that it should appear on the font list but it doesn't. Am I missing something. Phil I believe a font must be installed. I'm not sure ...
- Sat Dec 13, 2008 4:56 pm
- Forum: Aspire - Tips and Tricks
- Topic: Making a Tower or Wall
- Replies: 22
- Views: 13544
Re: Making a Tower or Wall
Excellent work Ted, Thanks for sharing your technique.
- Sat Dec 13, 2008 3:06 pm
- Forum: Aspire - General
- Topic: upgrading
- Replies: 3
- Views: 2637
Re: upgrading
I have been wanting to get Aspire since I saw Tony present it at John Forney's camp shopbot. I need to cut a job that Cut 2d or Vcarve pro this week but I want to purchase Aspire. If I purchase Vcarve pro now and Up grade Immediately will I still get the upgrade discount? As of this time I do not h...
- Wed Dec 10, 2008 12:29 pm
- Forum: Aspire - General
- Topic: Almost Made a HUGE Mistake
- Replies: 9
- Views: 5175
Re: Almost Made a HUGE Mistake
Words of wisdom. adding to that, I will never post a paying customer's work unless they have specifically said they were ok with it. There have been many litho's i would have loved to share but it belongs to them and I have to respect there wishes. I have downloaded many crv files in the past but ch...