Search found 916 matches

by CRFultz
Tue Dec 08, 2009 10:14 am
Forum: Aspire - General
Topic: Aspire V2.5 Released
Replies: 91
Views: 61834

Re: Aspire V2.5 Released

Nice work guys, thank you. Hope you all have a good Christmas

Chuck
by CRFultz
Tue Dec 30, 2008 11:38 am
Forum: PhotoVCarve - General
Topic: What am i doing wrong?
Replies: 9
Views: 5218

Re: What am i doing wrong?

I am using Oak. I am cutting it with a 60 degree engraving bit. I am putting 2 coats of Shellac on the surface. I am programming the line spacing at 130% The depth is .048 The angle is 35. I cut the picture Then i put a dark stain all over the picture and then wipe it off the top. My carvings are a...
by CRFultz
Tue Dec 23, 2008 11:08 pm
Forum: Aspire - General
Topic: Hey Every one Happy Holidays!
Replies: 10
Views: 5068

Re: Hey Every one Happy Holidays!

Merry Christmas everyone. It has been a pleasure being part of the Vectric family.

Chuck
by CRFultz
Sun Dec 21, 2008 11:41 am
Forum: Cut3D - General
Topic: Newbie Confuused on definition
Replies: 8
Views: 4517

Re: Newbie Confuused on definition

Tom you can rough it in with the 1/4 and finish with the 1/8th with a small stepover. 1/4 may not be enough depth to get the most out of what is possible
by CRFultz
Sun Dec 21, 2008 11:37 am
Forum: VCarve - Gallery
Topic: Candle holder, Thank you Khalid
Replies: 8
Views: 5298

Re: Candle holder, Thank you Khalid

Nice work guys, very creative
by CRFultz
Sun Dec 21, 2008 11:35 am
Forum: VCarve - General
Topic: need come creative design help
Replies: 1
Views: 1516

Re: need come creative design help

Will this work? :D :wink:
by CRFultz
Sun Dec 21, 2008 11:28 am
Forum: Aspire - Tips and Tricks
Topic: Roman Horses
Replies: 12
Views: 8225

Re: Roman Horses

Mark to change the height of the uppermost horse without affecting the others would require that horse to be seperated from the model. Tracing and cookie cutting might be your only option
by CRFultz
Sun Dec 21, 2008 11:22 am
Forum: Aspire - General
Topic: Need help please
Replies: 3
Views: 2651

Re: Need help please

You can make a circle around the center component (the bitmap) and make a planer shape from it with a height greater then what you currently have, that will raise it up. Make sure you place it at the top of the list in the Component manager.
by CRFultz
Sun Dec 21, 2008 11:06 am
Forum: Aspire - General
Topic: New to Aspire
Replies: 6
Views: 4047

Re: New to Aspire

Anthony, in the same run just make a text box and add your text the same has VCP. when you get ready to Vcarve or profile the text, click the box "Project toolpath onto 3d model" Make sure you have a safe Z when you run the job.
by CRFultz
Sun Dec 14, 2008 4:58 pm
Forum: Aspire - General
Topic: adding fonts
Replies: 9
Views: 5342

Re: adding fonts

Still can't get it to work. When VCarve or Aspire is first installed it "installs" fonts that are on the computer. Is there a way to do this step again without reinstalling? I'd appreciate some input from Tony or Brian. Aspire access's the TTf folder everytime it starts. Any changes (added or delea...
by CRFultz
Sun Dec 14, 2008 4:41 pm
Forum: PhotoVCarve - General
Topic: Bit question
Replies: 9
Views: 5641

Re: Bit question

Hi Crocky You mentioned an editor called Emeditor. Where can I get the software. Also, when I finish the carvings in wood do I need to apply stain to make the image visible as I cannot make out the image after carving. Ed Ed there are many different variations on finishing. Most I believe would use...
by CRFultz
Sun Dec 14, 2008 12:17 pm
Forum: Aspire - General
Topic: adding fonts
Replies: 9
Views: 5342

Re: adding fonts

I've done this before but for some reason I can't add fonts. I put the desired TTF font in the font folder for Aspire and then start the program. My understanding is that it should appear on the font list but it doesn't. Am I missing something. Phil I believe a font must be installed. I'm not sure ...
by CRFultz
Sat Dec 13, 2008 4:56 pm
Forum: Aspire - Tips and Tricks
Topic: Making a Tower or Wall
Replies: 22
Views: 13410

Re: Making a Tower or Wall

Excellent work Ted, Thanks for sharing your technique.
by CRFultz
Sat Dec 13, 2008 3:06 pm
Forum: Aspire - General
Topic: upgrading
Replies: 3
Views: 2601

Re: upgrading

I have been wanting to get Aspire since I saw Tony present it at John Forney's camp shopbot. I need to cut a job that Cut 2d or Vcarve pro this week but I want to purchase Aspire. If I purchase Vcarve pro now and Up grade Immediately will I still get the upgrade discount? As of this time I do not h...
by CRFultz
Wed Dec 10, 2008 12:29 pm
Forum: Aspire - General
Topic: Almost Made a HUGE Mistake
Replies: 9
Views: 5109

Re: Almost Made a HUGE Mistake

Words of wisdom. adding to that, I will never post a paying customer's work unless they have specifically said they were ok with it. There have been many litho's i would have loved to share but it belongs to them and I have to respect there wishes. I have downloaded many crv files in the past but ch...