Search found 59 matches
- Thu Jan 24, 2019 9:53 pm
- Forum: VCarve - General
- Topic: Router speed slows down
- Replies: 3
- Views: 1687
Router speed slows down
Hello When I set my feed rate it appears to be running normally at a given rate, but about 30m into the job the speed appears to slow down and it does this consistently. It's a hobby machine using chinese 23 oz. Steppers and a gecko 540 with 48v power supply. Are the motors overheating? Any ideas wo...
- Tue Jan 09, 2018 1:54 am
- Forum: VCarve - General
- Topic: masking peeling paint off of MDF
- Replies: 4
- Views: 3427
Re: masking peeling paint off of MDF
yes ur right, it dried fur 3 days and I agree it would a ppear that the primer failed.
- Tue Jan 09, 2018 12:41 am
- Forum: VCarve - General
- Topic: masking peeling paint off of MDF
- Replies: 4
- Views: 3427
masking peeling paint off of MDF
PaintPeeling.jpg Hello Could really use some help with masking on furniture grade MDF I have two failed attempts, on the first I applied spray can auto primer, Enamel spray paint and enamel spray can sealer. after carving and painting I went to remove the masking (Oramask stencil film 813) It peele...
- Fri Mar 18, 2016 3:26 am
- Forum: VCarve - General
- Topic: Tool deflection
- Replies: 8
- Views: 3863
Tool deflection
Hello I would like to know if there is tooling out there that resist deflection better than others. I get a lot of stair step when I profile to cutout the work from the main piece of wood. I use inexpensive end mills (1/8") that I get off of Ebay. If you have some brand names that would also be grea...
- Sat Feb 14, 2015 8:52 pm
- Forum: VCarve - General
- Topic: machine travel speed
- Replies: 2
- Views: 4082
Re: machine travel speed
Thanks ozymax
that helps
that helps
- Fri Feb 13, 2015 8:14 pm
- Forum: VCarve - General
- Topic: machine travel speed
- Replies: 2
- Views: 4082
machine travel speed
Hello My cnc travel, once it has lifted up and bound for a new location is the same speed as when it is cutting. I didn't even notice that this was an issue until I noticed that in some u tube videos that their machines picked up speed once it was through cutting and going to new location to cut. I ...
- Fri Jun 13, 2014 9:38 pm
- Forum: VCarve - General
- Topic: polyurethane finishing
- Replies: 5
- Views: 3371
Re: polyurethane finishing
Thanks for the replies I thin out the poly because It settles out the brush strokes and yes it does dry a bit faster as you mentioned. The actual stained finish looks great, it is the act of sanding the poly that I have issues with. I deff agree first coat is rough, but the problem is for me at leas...
- Fri Jun 13, 2014 5:45 am
- Forum: VCarve - General
- Topic: polyurethane finishing
- Replies: 5
- Views: 3371
polyurethane finishing
Hello I believe that finally I have been able to get a decent stained finish on pine. My latest project was looking good with general finishes gel stain. The problem is and where it went wrong was when I applied the satin poly over the stain, it contain a lot of dust nibs that really detracted from ...
- Thu May 22, 2014 12:20 pm
- Forum: VCarve - General
- Topic: working with warped wood
- Replies: 3
- Views: 2754
Re: working with warped wood
I guess I will have to try to surface that back of the item as I generally prefinish the surface.
- Thu May 22, 2014 11:23 am
- Forum: VCarve - General
- Topic: working with warped wood
- Replies: 3
- Views: 2754
working with warped wood
Hello
My carvings are off due to my wood being slightly warped. As the v bit travels From left to right, it cuts deeper into the wood causing undesirable results.
I don't own a planer and aside from surfacing the wood with the cnc, is there any tricks to compensate for this issue.
Thanks
Ken
My carvings are off due to my wood being slightly warped. As the v bit travels From left to right, it cuts deeper into the wood causing undesirable results.
I don't own a planer and aside from surfacing the wood with the cnc, is there any tricks to compensate for this issue.
Thanks
Ken
- Mon May 12, 2014 5:23 am
- Forum: VCarve - General
- Topic: I need a good 1/4" flat bottom end mill
- Replies: 12
- Views: 9059
Re: I need a good 1/4" flat bottom end mill
TReischl That is very interesting, I did not realize the reason for the dish and tapered corners and it makes perfect sense of course. You certainly learn something new everyday. Ok than I guess that best way to address the issue is to find which areas in which this occurs by looking at the tool pat...
- Sun May 11, 2014 5:35 pm
- Forum: VCarve - General
- Topic: I need a good 1/4" flat bottom end mill
- Replies: 12
- Views: 9059
Re: I need a good 1/4" flat bottom end mill
What is the benefit to a raidus/tapered corner versus a square?
Thanks
Thanks
- Sat May 10, 2014 8:26 pm
- Forum: VCarve - General
- Topic: I need a good 1/4" flat bottom end mill
- Replies: 12
- Views: 9059
Re: I need a good 1/4" flat bottom end mill
Hello The real problem i suppose is that because im clearing the area with a tool that's really just to big, i should just pocket with a smaller diameter tool. The clearing tool would just plunge down once to depth, lift out and than i would change to the smaller diameter tool to finish the balance ...
- Sat May 10, 2014 1:10 am
- Forum: VCarve - General
- Topic: I need a good 1/4" flat bottom end mill
- Replies: 12
- Views: 9059
I need a good 1/4" flat bottom end mill
Hello Another question. I'm looking for a suggestion for a 1/4" end mill that leaves a clean bottom. The ones that I have all leave a small raised circle the size of the bit when it touches down once and than leaves the area. When the smaller diameter bit comes into the area to clean up, it works ar...
- Wed May 07, 2014 3:43 am
- Forum: VCarve - General
- Topic: bad finishing experience
- Replies: 9
- Views: 5636
Re: bad finishing experience
Martin54 The below is the description for the mask I purchased. Oracal 813 Stencil Film is a rigid 3 mil translucent blue PVC stencil film has been formulated for stencil applications, especially spray and paint techniques. Can be used to mask surfaces to be painted and for die cut/hand cut spray ma...