Job Sheet doesn't show design
Job Sheet doesn't show design
A newbie here... I made a design for a tray for my bits; all good. But when I print the job sheet, it doesn't show the design in "Job Layout." What am I missing???
I'm attaching the .crv file and a pdf of the job sheet.
Thanks, everyone!
I'm attaching the .crv file and a pdf of the job sheet.
Thanks, everyone!
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: Job Sheet doesn't show design
There are tiny objects off in the FAR lower right. They're off your drawing. Delete them and all is well.
Re: Job Sheet doesn't show design
Thanks, GKAS, you were right "on the money." Not sure how they got there, but that did the trick. I'll know to look for that in the future. Thanks for helping a newcomer!
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: Job Sheet doesn't show design
No problem, we've all been there. I think the mistake is made by drawing by accident while in a 'draw' mode. Accidental mouse clicks.
Re: Job Sheet doesn't show design
Your sympathy is appreciated! Quite a learning curve on this all. Thanks again.
BTW: We are both Axiom owners - I just got an AR 6 Pro+ as my first CNC.
BTW: We are both Axiom owners - I just got an AR 6 Pro+ as my first CNC.
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: Job Sheet doesn't show design
There is an Axiom forum at http://axiomprecision.proboards.com/
Re: Job Sheet doesn't show design
Thanks. I knew about that.
Also noted that you have the Axiom Laser. I've just got it mounted and am looking for good test projects. Any suggestions?
Also noted that you have the Axiom Laser. I've just got it mounted and am looking for good test projects. Any suggestions?
- gkas
- Vectric Wizard
- Posts: 1451
- Joined: Sun Jan 01, 2017 3:39 am
- Model of CNC Machine: Aspire, Axiom AR8 Pro+, Axiom 4.2W Laser
- Location: Southern California
Re: Job Sheet doesn't show design
I ran a series of small squares, and sets of lettering to test. Each done 20 ipm, 40 ipm, 60 ipm 80 ipm and 100 ipm. This is what I use to test a cut in new material; felt, thin board, cardboard, etc. I do the same for the engrave text. Each time I use a file, I duplicate it and I either remove the ones I think will not be in range, or dupe a range to get finer gradiations. You don't want to test cardboard at 20 ips. You can lengthen the burn times by using the 'Speed Scale Adjustment' (Y+/- buttons) to decrease the ips. 100 ips is a pretty light burn. You can't increase it beyond the factor of '1'. If you decrease to 50% (0.5), then you change 100 ips to 50 ips (or pretty close).
I save these test files, and pretty soon you have a good set of test runs. You CANNOT control the intensity of the laser, only the duration using different speeds. There is a connection on the laser for an intensity, but no way to control it from the Axiom.
I cut felt liners, game pieces, tiny wood pieces, and some logos. I do engrave my signature in the backs of some of my pieces.
I save these test files, and pretty soon you have a good set of test runs. You CANNOT control the intensity of the laser, only the duration using different speeds. There is a connection on the laser for an intensity, but no way to control it from the Axiom.
I cut felt liners, game pieces, tiny wood pieces, and some logos. I do engrave my signature in the backs of some of my pieces.
- Mark Jones
- Vectric Craftsman
- Posts: 144
- Joined: Fri Aug 28, 2020 8:38 pm
- Model of CNC Machine: Shark HD 5
- Location: Ozark
- Contact:
Re: Job Sheet doesn't show design
Does anyone have a vcarve file for the 2 watt laser to show the various power and speed settings and what it looks like after a test burn on a sample piece of material?
I know I have seen them somewhere but can't remember where.
Any help is much appreciated.
Mark Jones
I know I have seen them somewhere but can't remember where.
Any help is much appreciated.
Mark Jones
Mark Jones
- scotttarnor
- Vectric Wizard
- Posts: 945
- Joined: Fri Aug 30, 2019 11:40 pm
- Model of CNC Machine: Piranha XL , Shark HD520
- Location: La Crosse WI
Re: Job Sheet doesn't show design
Scott T
@scottscnc
@scottscnc
- Mark Jones
- Vectric Craftsman
- Posts: 144
- Joined: Fri Aug 28, 2020 8:38 pm
- Model of CNC Machine: Shark HD 5
- Location: Ozark
- Contact:
Re: Job Sheet doesn't show design
Thanks Scott. That is exactly what I needed. Will get to it in a bit.
Mark Jones