Engrave raised letters on a 3D surface
Engrave raised letters on a 3D surface
Hi,
I often need to engrave raised letters on a 3D surface. Vcarve seems to do the job but when i simulate the toolpaths with Cut depth set to 0 1 mm i´m can not see the material removal. How to solve this issue ?
I only see material removal when the the Cut depth is set to 1.0 mm but doing this i´m cutting bellow the surface i´ve imported. Is there a way to impose a clearence on a 3D toolpath ?
My steps were ;
1- Import stl 3d model . The imported surface is where i need to palce the raised letters.
2-Create 2d vectors
3- Create toolpath and project them on the 3d surface.
4- Simulate , but i do not see material removal.
Thanks
Regards,
M Dias
I often need to engrave raised letters on a 3D surface. Vcarve seems to do the job but when i simulate the toolpaths with Cut depth set to 0 1 mm i´m can not see the material removal. How to solve this issue ?
I only see material removal when the the Cut depth is set to 1.0 mm but doing this i´m cutting bellow the surface i´ve imported. Is there a way to impose a clearence on a 3D toolpath ?
My steps were ;
1- Import stl 3d model . The imported surface is where i need to palce the raised letters.
2-Create 2d vectors
3- Create toolpath and project them on the 3d surface.
4- Simulate , but i do not see material removal.
Thanks
Regards,
M Dias
- Adrian
- Vectric Archimage
- Posts: 14684
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: Engrave raised letters on a 3D surface
What preview resolution are you using (Toolpaths menu/Preview Simulation Quality). If it's anything other than Maximum try that setting and preview it again.
Are you going to be able to cut 0.1mm deep letters in reality though? You would need completely accurate z-zero setting and material positioning for that to work.
Are you going to be able to cut 0.1mm deep letters in reality though? You would need completely accurate z-zero setting and material positioning for that to work.
Re: Engrave raised letters on a 3D surface
Sorry i meant 1 mm not 0.1 mm.
The simulation is working fine. I don´t see material removal because i ám not able not create a toolpath offseting 1.0 mm from the surface i´ve imported . Is there a way to do this ?
M Dias
The simulation is working fine. I don´t see material removal because i ám not able not create a toolpath offseting 1.0 mm from the surface i´ve imported . Is there a way to do this ?
M Dias
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Engrave raised letters on a 3D surface
Hi Manuel,
It may be easier to get spot-on advice if you will post a download link to your actual file (using a free file transfer service such as DropBox).
That way, we can see exactly how you are laying out your project, observe your material setup (for any gaps) and how you have created your toolpaths. It's sometimes difficult to "guess" what the problem might be unless the file itself is available.
It may be easier to get spot-on advice if you will post a download link to your actual file (using a free file transfer service such as DropBox).
That way, we can see exactly how you are laying out your project, observe your material setup (for any gaps) and how you have created your toolpaths. It's sometimes difficult to "guess" what the problem might be unless the file itself is available.
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- TReischl
- Vectric Wizard
- Posts: 4657
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: Engrave raised letters on a 3D surface
I am not sure how one "engraves" raised letters on a surface.
The only way to create raised letters is to remove material around them, as in pocketing or profiling outside of them. Not being picky about terminology here. . . .
The only way to RAISE letters on an imported surface is to remove material around them.
So, what are you trying to do? A pick would be helpful.
The only way to create raised letters is to remove material around them, as in pocketing or profiling outside of them. Not being picky about terminology here. . . .
The only way to RAISE letters on an imported surface is to remove material around them.
So, what are you trying to do? A pick would be helpful.
"If you see a good fight, get in it." Dr. Vernon Johns
Re: Engrave raised letters on a 3D surface
Taking the picture from your post as reference.
. If you import the surface and then create the toolpath for projecting it on the surface.
Try to machine the raised letters but without cutting /touching on the imported surface ?
. If you import the surface and then create the toolpath for projecting it on the surface.
Try to machine the raised letters but without cutting /touching on the imported surface ?
- TReischl
- Vectric Wizard
- Posts: 4657
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: Engrave raised letters on a 3D surface
Use the "project toolpath onto 3d model" and choose a very shallow depth of cut, like .0001manueldiasmanuel wrote:Taking the picture from your post as reference.
. If you import the surface and then create the toolpath for projecting it on the surface.
Try to machine the raised letters but without cutting /touching on the imported surface ?
"If you see a good fight, get in it." Dr. Vernon Johns
Re: Engrave raised letters on a 3D surface
I can do it easily , the only question is about validating the result.
I have to use engraving tools with 15 degrees per side and with 0.15 mm of diameter . To avoid break the tool i have to use multipasses on Z.
Before i machine with the engrave tool i use a ball mill to machine the surface around the letters , so only a good simulation could assure me a good result otherwise i will be cutting material without knowing what is going to happen, and why.
So the simulation it´s very important for me. Any ideas ?
Thanks,,
M Dias
- TReischl
- Vectric Wizard
- Posts: 4657
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: Engrave raised letters on a 3D surface
Ok, correct me if I am wrong. . .
You are ENGRAVING letters into a mold. The part produced by the mold has RAISED letters. There are no RAISED letters in the mold. So there is no need to talk about raised letters.
I would not expect to be able to see anything a .0059 inch diameter did. I have the same issue with the laser on my machine. I have it set at .007 diameter. You should be able to see the preview if you set your preview quality a lot higher. If I use Standard I cannot see what the laser beam is doing at all.
By the way, I do not know why you expect to be able to see the tool cutting if you OFFSET the tool above the surface. Think about it, if the surface has been cut and you offset above it there is nothing there to cut so you should not see anything.
You are ENGRAVING letters into a mold. The part produced by the mold has RAISED letters. There are no RAISED letters in the mold. So there is no need to talk about raised letters.
I would not expect to be able to see anything a .0059 inch diameter did. I have the same issue with the laser on my machine. I have it set at .007 diameter. You should be able to see the preview if you set your preview quality a lot higher. If I use Standard I cannot see what the laser beam is doing at all.
By the way, I do not know why you expect to be able to see the tool cutting if you OFFSET the tool above the surface. Think about it, if the surface has been cut and you offset above it there is nothing there to cut so you should not see anything.
"If you see a good fight, get in it." Dr. Vernon Johns
Re: Engrave raised letters on a 3D surface
Yes, you are wrong.
The part produced by the mold has engraved letters not RAISED. I need the mold with RAISED letters
I expect to see the tool cutting above the surface, for that the solution would be to create a finishing machining toolpath but with an allowance value to have an offset above the relief for the machining. After this step i could create engraving toolpath and see the material being removed , agree ?
This is the way i do it on others softwares.
Where should i go to ask for this feature or is there any way to do it with VCarve ?
Thanks,
M Dias
The part produced by the mold has engraved letters not RAISED. I need the mold with RAISED letters
I expect to see the tool cutting above the surface, for that the solution would be to create a finishing machining toolpath but with an allowance value to have an offset above the relief for the machining. After this step i could create engraving toolpath and see the material being removed , agree ?
This is the way i do it on others softwares.
Where should i go to ask for this feature or is there any way to do it with VCarve ?
Thanks,
M Dias
- Adrian
- Vectric Archimage
- Posts: 14684
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: Engrave raised letters on a 3D surface
Create a vector that is the same size as the curved area of the dish. Now create a Pocket toolpath set to 0.1mm making sure you have the text AND the new vectors selected not forgetting to check the Project onto 3D surface. That toolpath will remove 0.1mm of material from the surface of the dish leaving the text alone but curved to conform to the dish.
Example here - https://www.dropbox.com/sh/pktrqfxvh01k ... GHEla?dl=0
In Aspire you could do the whole operation as a 3D toolpath as you can create the raised text directly. With VCarve you either have to create the text as part of the 3D model with another program or do something as I've suggested.
Example here - https://www.dropbox.com/sh/pktrqfxvh01k ... GHEla?dl=0
In Aspire you could do the whole operation as a 3D toolpath as you can create the raised text directly. With VCarve you either have to create the text as part of the 3D model with another program or do something as I've suggested.
-
- Vectric Apprentice
- Posts: 89
- Joined: Thu Mar 20, 2014 9:52 pm
- Model of CNC Machine: Flexicam Stealth
Re: Engrave raised letters on a 3D surface
I realize this post is a couple of years old, but the issue is a brand new problem for me.
Is it summarily true that the task of modeling (and perhaps milling) raised letters in Aspire is an oversight or glitch on the part of Vectric? If not, why all the chicanery to "get around" the issue?
It's a given that raised letters are ONLY possible by removing material, ironically just like engraving letters. Only big, big difference is the former leaves the letters by removing material OUTSIDE their respective vectors, while engraving cuts away material that map the letters. In the art world, the raised letters are bas relief.
My attempt at leaving raised letters on a 3D surface by raster cutting with various tools predictably left very jagged peripheral edges. What I really want are profile cut letters........easy enough with flat sheet goods, but an apparent nightmare when projected on sculpted surfaces.
If there is no issue, then why can't we see the raised letters in straight forward manner when toolpathing in the 3D view?
My after the fact guess is select all vectors that describe the letters as untouchables when milling the other components.
Is it summarily true that the task of modeling (and perhaps milling) raised letters in Aspire is an oversight or glitch on the part of Vectric? If not, why all the chicanery to "get around" the issue?
It's a given that raised letters are ONLY possible by removing material, ironically just like engraving letters. Only big, big difference is the former leaves the letters by removing material OUTSIDE their respective vectors, while engraving cuts away material that map the letters. In the art world, the raised letters are bas relief.
My attempt at leaving raised letters on a 3D surface by raster cutting with various tools predictably left very jagged peripheral edges. What I really want are profile cut letters........easy enough with flat sheet goods, but an apparent nightmare when projected on sculpted surfaces.
If there is no issue, then why can't we see the raised letters in straight forward manner when toolpathing in the 3D view?
My after the fact guess is select all vectors that describe the letters as untouchables when milling the other components.
- Adrian
- Vectric Archimage
- Posts: 14684
- Joined: Thu Nov 23, 2006 2:19 pm
- Model of CNC Machine: ShopBot PRS Alpha 96x48
- Location: Surrey, UK
Re: Engrave raised letters on a 3D surface
This thread is about VCarve not Aspire which is why the process given here might sound a bit convoluted to an Aspire user.2C3D4U wrote: ↑Tue Apr 13, 2021 1:25 am
Is it summarily true that the task of modeling (and perhaps milling) raised letters in Aspire is an oversight or glitch on the part of Vectric? If not, why all the chicanery to "get around" the issue?
If there is no issue, then why can't we see the raised letters in straight forward manner when toolpathing in the 3D view?
My after the fact guess is select all vectors that describe the letters as untouchables when milling the other components.
Not sure what you mean about not being able to see the raised letters in a straightforward manner. You can see them in both products.
Could you elaborate a bit more on what issues you're having and if you could attach a file that would help as well? There are many setup issues that can lead to edges more jagged than they need to be.
Using a profile toolpath to clean them up if you have all the settings correct and still aren't happy with the finish. Also it's possible to create the text as a component and apply a slight draft to it which also cleans up the vertical edges.
-
- Vectric Apprentice
- Posts: 89
- Joined: Thu Mar 20, 2014 9:52 pm
- Model of CNC Machine: Flexicam Stealth
Re: Engrave raised letters on a 3D surface
When I say "see the raised text in straight forward manner", I mean having a utility (click of a button) that smoothly mills the vertical sides of raised text merged with a 3D model so that the letters are profile milled with the bit varying in Z up and down the underlying component without any scarring.
- martin54
- Vectric Archimage
- Posts: 7355
- Joined: Fri Nov 09, 2012 2:12 pm
- Model of CNC Machine: Gerber 48, Triac PC, Isel fixed gantry
- Location: Kirkcaldy, Scotland
Re: Engrave raised letters on a 3D surface
Pictures always help as I am guessing your file might be copyright protected. Screenshots of what you are trying to achieve may help.
If it is just being able to see a visual clearly then check what resolution you have the toolpath preview simulation set at. Just be aware that the higher you set it the longer the simulation will take to render
If it is just being able to see a visual clearly then check what resolution you have the toolpath preview simulation set at. Just be aware that the higher you set it the longer the simulation will take to render