US Flag on Work Shop
- TReischl
- Vectric Wizard
- Posts: 4600
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
US Flag on Work Shop
I have been working on this one awhile. It measures 36 inches long by about 22 tall. Mounted it below the all night shop light. I am not much of a photographer soooo. . . . .
Here is one my wife took, she is obviously better with a camera!
Here is one my wife took, she is obviously better with a camera!
"If you see a good fight, get in it." Dr. Vernon Johns
- CrowsWW
- Vectric Craftsman
- Posts: 155
- Joined: Wed Jun 27, 2012 7:10 pm
- Model of CNC Machine: ShopSabre 4896
- Location: Palmer, Alaska USA
Re: US Flag on Work Shop
That looks real nice. Great Job!
Troy Crow
Crow's Woodwork's
I have a day job to support my wood habit!
Crow's Woodwork's
I have a day job to support my wood habit!
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: US Flag on Work Shop
Beautiful work Ted, you're getting some mileage out of that eagle.
John
Maker of Chips
Maker of Chips
-
- Vectric Craftsman
- Posts: 216
- Joined: Sat Feb 03, 2018 2:03 am
- Model of CNC Machine: diy 4 X 4 CNC Router
- Location: So. Cal.
Re: US Flag on Work Shop
Love the theme.
Take a picture in day light and post.
Looks great.
mark-s
Take a picture in day light and post.
Looks great.
mark-s
- Todd Bailey
- Vectric Staff
- Posts: 622
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Re: US Flag on Work Shop
Hello TReischl...
That looks FANTASTIC!!! Well done! Thanks for sharing.
That looks FANTASTIC!!! Well done! Thanks for sharing.
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com
Re: US Flag on Work Shop
Plus 1Love the theme.
Take a picture in day light and post.
Looks great.
mark-s
Gary
- dwilli9013
- Vectric Wizard
- Posts: 1237
- Joined: Mon Sep 30, 2013 12:45 am
- Model of CNC Machine: 3 axis Self Designed Self Built
- Location: Machesney Park Illinois
Re: US Flag on Work Shop
Very Nice Ted. The lighting gives it a very cool effect. Thanks for sharing.
D-Dub
Dwayne
Dwilli
Dwayne
Dwilli
- TReischl
- Vectric Wizard
- Posts: 4600
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: US Flag on Work Shop
OK, my better half got a nice pic this evening:
This actually shows the waves in the flag. Taken right near sunset.
Thanks for all the compliments!!!!
This actually shows the waves in the flag. Taken right near sunset.
Thanks for all the compliments!!!!
"If you see a good fight, get in it." Dr. Vernon Johns
- mtylerfl
- Vectric Archimage
- Posts: 5865
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: US Flag on Work Shop
That looks fantastic, Ted!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
- scottp55
- Vectric Wizard
- Posts: 4714
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: US Flag on Work Shop
VERY Nice Ted!!
Looks VERY deep...What was total depth, and where was the spot most in danger from the collet nut(before clearing)?
LIKING it!
scott
Looks VERY deep...What was total depth, and where was the spot most in danger from the collet nut(before clearing)?
LIKING it!
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.
- mezalick
- Vectric Wizard
- Posts: 2970
- Joined: Mon Nov 03, 2008 9:07 am
- Model of CNC Machine: Camaster Cobra
- Location: Philadelphia, PA USA
- Contact:
Re: US Flag on Work Shop
Last picture looks great.
Nice work.
Michael
Nice work.
Michael
Michael Mezalick
https://www.youtube.com/user/mezalick
mm@mezalick.com
https://www.youtube.com/user/mezalick
mm@mezalick.com
- TReischl
- Vectric Wizard
- Posts: 4600
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: US Flag on Work Shop
Total depth is 2.7 inches. The deepest place was along the eagle's throat. That was an issue because I had neglected to add a bit of taper and the software was cutting inwards towards the center at that point so all the material was still there. What I did was define an oval area around the throat so that it would cut from the inside out removing the step of material first.scottp55 wrote:VERY Nice Ted!!
Looks VERY deep...What was total depth, and where was the spot most in danger from the collet nut(before clearing)?
LIKING it!
scott
My biggest challenge these days is painting. My first issue is that I get in too much of a hurry to see a project completed (aka the little boy syndrome). Second is prep, I am getting much better about that. Third is the type of paint. Latex is great to work with, fast drying, easy cleanup, etc, but I am starting to think that oil based paints produce better results.
The flag is made from big box pine that I made sure had dried out. I culled it for knots, ripped it to the 2.7 thickness, flattened both sides and then face glued it. Pine gets a bad rap all the time because it rots. That is both true and false. If you paint pine and then mount it so that water cannot be trapped on its surface it will last longer than most of us. So what I do is use standoffs on the backside so the water is not trapped between the sign and the building. I just use a couple of thin strips of white oak which is highly rot resistant in a vertical position. That way water is never trapped behind the sign. I sort of figured this out by looking where some adirondack chairs I built about twenty years ago had started to rot. Of course on the bottom of the legs from wicking water up and also wherever there were any places that water would get trapped, like where the back slats met the seat.
There are a couple of reasons I do not just use treated SYP. First is that the dust from it is downright unhealthy, secondly is that it sands lousy, third is that it is really fast growing which makes for huge grain that tends to splinter easily when cutting.
I am not in the mode of building monuments that future generations will "Oooo, and Ahhhhh!" More than likely whoever buys this place after they plant us will say "What is with that flag? It's gotta go!" or maybe not, in which case they can get out their paint brushes and give it another coat. I did use stainless steel screws to mount it so that they do not rust and run down the face of the flag.
"If you see a good fight, get in it." Dr. Vernon Johns
- scottp55
- Vectric Wizard
- Posts: 4714
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: US Flag on Work Shop
Thanks Ted!! Hadn't thought of that.Total depth is 2.7 inches. The deepest place was along the eagle's throat. That was an issue because I had neglected to add a bit of taper and the software was cutting inwards towards the center at that point so all the material was still there. What I did was define an oval area around the throat so that it would cut from the inside out removing the step of material first.
Yep, Aspire Would come in handy to give a little slope to a near vertical surface!
Maybe one day
Thanks!!
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.
- mtylerfl
- Vectric Archimage
- Posts: 5865
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: US Flag on Work Shop
Ted,
Did you take any photos of the raw glue-up and photos during/after the carve (before painting)?
Did you take any photos of the raw glue-up and photos during/after the carve (before painting)?
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC