U.S. Wavy flag (thanks to TReischl) with eagle head.
Maple 7/16 thick, 3 X 5 , straight off the machine, no clean up
or finish.
1 mm ball nose bit for the carve and a 3/16 down cut for profile.
Maple was from an old cabinet draw side, Maple carves so nice,
very little clean up.
mark-s
U.S. Wavy flag (TReischl) with eagle head.
- WNC_Ed
- Vectric Craftsman
- Posts: 296
- Joined: Fri Dec 07, 2018 5:56 pm
- Model of CNC Machine: Shark HD4 AXYZ 4010
- Location: Western North Carolina - Heart of the Smokies
Re: U.S. Wavy flag (TReischl) with eagle head.
Very nice!
Looking forward to a finished pic.
Congrats on a job well done.
Looking forward to a finished pic.
Congrats on a job well done.
Maker of sawdust
- TReischl
- Vectric Wizard
- Posts: 4645
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: U.S. Wavy flag (TReischl) with eagle head.
Looks good! Happy to see at least one person getting some use from the model.
Apparently you are having a lot of fun with those .25R tapered ball nose bits. I love em myself. But. . . .
I am cutting a flag that is 36 X 22 X 2.75 thick right now. No .25R ball nose on that one!
I have cut out a smaller one like yours and am just putting on the finishing touches to the paint job. I may easily be the world's worst painter, especially small stuff like that. Houses? No problem.
Apparently you are having a lot of fun with those .25R tapered ball nose bits. I love em myself. But. . . .
I am cutting a flag that is 36 X 22 X 2.75 thick right now. No .25R ball nose on that one!
I have cut out a smaller one like yours and am just putting on the finishing touches to the paint job. I may easily be the world's worst painter, especially small stuff like that. Houses? No problem.
"If you see a good fight, get in it." Dr. Vernon Johns
-
- Vectric Craftsman
- Posts: 216
- Joined: Sat Feb 03, 2018 2:03 am
- Model of CNC Machine: diy 4 X 4 CNC Router
- Location: So. Cal.
Re: U.S. Wavy flag (TReischl) with eagle head.
What bit would you use?
Roughing pass, size bit?
Do like that 0.25 BN bit for small stuff.
Thanks
mark-s
Roughing pass, size bit?
Do like that 0.25 BN bit for small stuff.
Thanks
mark-s
- TReischl
- Vectric Wizard
- Posts: 4645
- Joined: Thu Jan 18, 2007 6:04 pm
- Model of CNC Machine: 8020 48X36X7 RP 2022 UCCNC Screenset
- Location: Leland NC
Re: U.S. Wavy flag (TReischl) with eagle head.
Mark, if you are asking about the large flag I am working on. . . .
I used a 10mm HSS cutting 5mm deep at 350 IPM. Stepover was 7mm (70%). Roughing time was 1hr 42min
Finishing was a .25 ball nose at 150 IPM. Finishing was 5hrs 21min
The blank size was 38X24X2.75
Here is a link to a video of it cutting:
https://www.youtube.com/watch?v=tFA_1PJS32U&t=54s
Sanding and clean up, all afternoon.
I am not real thrilled with this eagle at a large size, way too muddy. So I got out my carving tools and am giving it some definition. It wasn't the .25 ball nose, it was the model itself. Someone went ape with smoothing or something. When it is all done I will post it up here.
I used a 10mm HSS cutting 5mm deep at 350 IPM. Stepover was 7mm (70%). Roughing time was 1hr 42min
Finishing was a .25 ball nose at 150 IPM. Finishing was 5hrs 21min
The blank size was 38X24X2.75
Here is a link to a video of it cutting:
https://www.youtube.com/watch?v=tFA_1PJS32U&t=54s
Sanding and clean up, all afternoon.
I am not real thrilled with this eagle at a large size, way too muddy. So I got out my carving tools and am giving it some definition. It wasn't the .25 ball nose, it was the model itself. Someone went ape with smoothing or something. When it is all done I will post it up here.
"If you see a good fight, get in it." Dr. Vernon Johns
-
- Vectric Craftsman
- Posts: 216
- Joined: Sat Feb 03, 2018 2:03 am
- Model of CNC Machine: diy 4 X 4 CNC Router
- Location: So. Cal.
Re: U.S. Wavy flag (TReischl) with eagle head.
Thank you for the info.
mark-s
mark-s