Holy Week Test Cuts in 3/4 Poplar

An area to upload images of pieces cut using VCarve Pro

Holy Week Test Cuts in 3/4 Poplar

Postby Rcnewcomb » Wed Apr 17, 2019 12:49 am

About 0.4" deep and about 4x5 to 7x9
Rough 10 minutes with a 1/4" end mill.
Finish pass using a 1/16 tapered ballnose with a 7% stepover at 180IPM and 18K RPM for 57 minutes per panel.
Attachments
TestCutIMG_0644.jpg
TestCutIMG_0646.jpg
TestCutIMG_0647.jpg
- Randall Newcomb
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3568
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Holy Week Test Cuts in 3/4 Poplar

Postby ezurick » Wed Apr 17, 2019 7:07 am

Very nice! But how do you plan to use them? On furniture or something? Just curious.
User avatar
ezurick
Vectric Craftsman
 
Posts: 282
Joined: Sat Oct 20, 2018 1:27 pm
Model of CNC Machine: Chinese 6040

Re: Holy Week Test Cuts in 3/4 Poplar

Postby Rcnewcomb » Wed Apr 17, 2019 4:23 pm

In Florence,Italy I saw church doors with sets of carvings. Ghiberti created a set I admire. I thought it might be interesting to make a door for my local church. I’m not sure how soon this would happen, but these were some test cuts.
- Randall Newcomb
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3568
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Holy Week Test Cuts in 3/4 Poplar

Postby Rcnewcomb » Wed Apr 17, 2019 7:52 pm

- Randall Newcomb
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3568
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Holy Week Test Cuts in 3/4 Poplar

Postby TReischl » Thu Apr 18, 2019 1:11 am

Ahhh, to be able to carve like that!!! ::::sigh:::::

Thanks for posting those pics Randy.
"If you see a good fight, get in it." Dr. Vernon Jones
User avatar
TReischl
Vectric Wizard
 
Posts: 2917
Joined: Thu Jan 18, 2007 6:04 pm
Location: Leland NC
Model of CNC Machine: 8020 Build 48X36X10 RP 2010 Screenset

Re: Holy Week Test Cuts in 3/4 Poplar

Postby highpockets » Thu Apr 18, 2019 1:15 am

I didn't know that had CNC machine way back then!!! :lol: :lol: :lol:
John
Maker of Chips
User avatar
highpockets
Vectric Wizard
 
Posts: 2499
Joined: Tue Jan 06, 2015 4:04 pm
Model of CNC Machine: PDJ Pilot Pro

Re: Holy Week Test Cuts in 3/4 Poplar

Postby ezurick » Tue Apr 23, 2019 6:23 am

highpockets wrote:I didn't know that had CNC machine way back then!!! :lol: :lol: :lol:



a [C]ouple of [N]uns w/ [C]hisels? lol.


But those carvings are really nice. Are these thin wood pieces carved, then glued to the door?
User avatar
ezurick
Vectric Craftsman
 
Posts: 282
Joined: Sat Oct 20, 2018 1:27 pm
Model of CNC Machine: Chinese 6040


Return to VCarve - Gallery

Who is online

Users browsing this forum: BigC and 8 guests