STL toolpathing issues
- adze_cnc
- Vectric Wizard
- Posts: 4325
- Joined: Sat Jul 27, 2013 10:08 pm
- Model of CNC Machine: AXYZ 4008
- Location: Vancouver, BC, Canada
Re: STL toolpathing issues
If anything screamed out "3D print me" then this model would be it. With each of those indentations 0.8mm you're going to need an awfully tiny bit to get those inside corners even close to "square".
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: STL toolpathing issues
This is closer to your design. You were right about putting things on different layers. Hopefully you can understand the process I was using. The original vectors from the DWG file are in layer 0. I copied them to different layers and cleaned them up for machinability. The V8.5 CRV file is attached.
Please ask questions and show us your progress.
Please ask questions and show us your progress.
- Attachments
-
- Split_bluetooth85V01_2.crv
- (553 KiB) Downloaded 78 times
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
- FixitMike
- Vectric Wizard
- Posts: 2173
- Joined: Sun Apr 17, 2011 5:21 am
- Model of CNC Machine: Shark Pro Plus (retired)
- Location: Burien, WA USA
Re: STL toolpathing issues
Question 1: Isn't the pass depth for the ThruProfile a little too much? 5.625 mm for a 2 mm dia. bit. Ditto for the StandoffPocket. Unless the material is foam.
Question 2:Does the 2mm end mill get fatter above the cutting portion? If it does I would check for interference with the standoffs and lip while cutting the ThruProfile and StandoffPocket. Easily fixed by making the standoffs round and making the lip (and material) a bit larger.
Question 3: Why the LipProfile toolpath? That edge is also cut by the StandoffPocket toolpath.
Question 4: What does the STL in the title refer to? I don't see any .STL files here. Nor would I expect to for this type of project.
Note: Spaces are permitted in toolpath and Layer names, if you so desire.
I suspect my questions are just covering things that ordinarily would be fixed before cutting.
Question 2:Does the 2mm end mill get fatter above the cutting portion? If it does I would check for interference with the standoffs and lip while cutting the ThruProfile and StandoffPocket. Easily fixed by making the standoffs round and making the lip (and material) a bit larger.
Question 3: Why the LipProfile toolpath? That edge is also cut by the StandoffPocket toolpath.
Question 4: What does the STL in the title refer to? I don't see any .STL files here. Nor would I expect to for this type of project.
Note: Spaces are permitted in toolpath and Layer names, if you so desire.
I suspect my questions are just covering things that ordinarily would be fixed before cutting.
Good judgement comes from experience.
Experience comes from bad judgement.
Experience comes from bad judgement.
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: STL toolpathing issues
Good questions/comments Mike. And as adze_cnc noted, this particular design might be better for 3D printing.
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
Re: STL toolpathing issues
Thanks to adze_cnc, I did end up 3D printing my design and have a working prototype to play around with.
Having something physical really does point of the flaws in a design. After getting slightly more comfortable with the software I realized how unfriendly my design was to Vcarve. Here's my redesign and subsequent attempt at creating a toolpath. Whats throwing me off is the 3D fillet I have on the standoff, what is the proper way to create that toolpath?
I hope it didn't seem like I just ran off with a completed toolpath! School work forced me into a mandatory hiatus but I've been working bit by bit as time allows.
Having something physical really does point of the flaws in a design. After getting slightly more comfortable with the software I realized how unfriendly my design was to Vcarve. Here's my redesign and subsequent attempt at creating a toolpath. Whats throwing me off is the 3D fillet I have on the standoff, what is the proper way to create that toolpath?
I hope it didn't seem like I just ran off with a completed toolpath! School work forced me into a mandatory hiatus but I've been working bit by bit as time allows.
-
- Vectric Wizard
- Posts: 1592
- Joined: Sun Sep 16, 2007 2:59 pm
- Model of CNC Machine: Custom DIY
- Location: Lake St Clair, MI, USA
- Contact:
Re: STL toolpathing issues
A profile toolpath with a ballnose tool of the appropriate size?Whats throwing me off is the 3D fillet I have on the standoff, what is the proper way to create that toolpath?
Gerry - http://www.thecncwoodworker.com
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: STL toolpathing issues
yes, what ger21 saidA profile toolpath with a ballnose tool of the appropriate size
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
Re: STL toolpathing issues
Worked perfectly I wouldn't have been able to make it this far without all your help. I'll be sure to post a final update when I get everything done.
Re: STL toolpathing issues
Question regarding the cut slots, would it be necessary to add tabs? or just more work on my end, I have switched to an 1/8" bit, but am worried about the bit breaking or jumping because of a loose piece.