Dining room table
- dealguy11
- Vectric Wizard
- Posts: 2494
- Joined: Tue Sep 22, 2009 9:52 pm
- Model of CNC Machine: Anderson Selexx 510,24x48 GCnC/WinCNC
- Location: Henryville, PA
Dining room table
No carvings on this, just a really big table that fitted together beautifully. Used Aspire to cut the "pie" pieces for the table top, and also the thick oak pieces around the edge. Also cut the large disks and rings that are inside the round base, and an underlayment piece to stiffen up the top. There is no filler on the pie pieces - they went together so precisely and closely that there were no gaps. Table is white oak with a cerused finish and is 84" in diameter.
Steve Godding
Not all who wander (or wonder) are lost
Not all who wander (or wonder) are lost
- dwilli9013
- Vectric Wizard
- Posts: 1237
- Joined: Mon Sep 30, 2013 12:45 am
- Model of CNC Machine: 3 axis Self Designed Self Built
- Location: Machesney Park Illinois
Re: Dining room table
Very Nice. Really like the ring around the outside. Someones lucky to receive this one.
D-Dub
Dwayne
Dwilli
Dwayne
Dwilli
-
- Vectric Wizard
- Posts: 1013
- Joined: Fri May 15, 2015 1:10 pm
- Model of CNC Machine: 3 axis small size machine
- Location: France
Re: Dining room table
I like this very simple but perfectly manufactured design.
Best regards
Didier
W7 - Aspire 8.517
Didier
W7 - Aspire 8.517
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Dining room table
Holy smokes, that is a gorgeous table, Steve! Looks perfect!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Craftsman
- Posts: 110
- Joined: Thu Jan 08, 2009 6:24 am
- Model of CNC Machine: CAMaster Stinger SR-23
- Location: Orange, CA
Re: Dining room table
WOW...
That is really a beautiful design and could not be more pleasing to the eye. Very well done, you should be very proud of your work.
Thanks for sharing.
Dan
That is really a beautiful design and could not be more pleasing to the eye. Very well done, you should be very proud of your work.
Thanks for sharing.
Dan
- mikeacg
- Vectric Wizard
- Posts: 659
- Joined: Sun Nov 02, 2008 10:53 pm
- Model of CNC Machine: Camaster Stinger, Sidewinder, SB 4x4
- Location: Newberry, MI
- Contact:
Re: Dining room table
Steve,
As always, beautiful work! Love the design and your execution is flawless...
Mike
As always, beautiful work! Love the design and your execution is flawless...
Mike
-
- Posts: 31
- Joined: Wed Oct 19, 2016 2:44 am
- Model of CNC Machine: ShopBot
- Location: Palm Coast, Florida
- Contact:
Re: Dining room table
Wonderful work!
Did you need to take any precautions to prevent the points of the pie from getting damaged while routing them out?
Did you need to take any precautions to prevent the points of the pie from getting damaged while routing them out?
https://www.syzygywoodworks.com
https://www.facebook.com/SyzygyWoodworks
https://www.facebook.com/SyzygyWoodworks
- dealguy11
- Vectric Wizard
- Posts: 2494
- Joined: Tue Sep 22, 2009 9:52 pm
- Model of CNC Machine: Anderson Selexx 510,24x48 GCnC/WinCNC
- Location: Henryville, PA
Re: Dining room table
No, not really. I cut them out with a 3/8" compression bit, which cuts down from the top and up from the bottom. This prevents the veneer from blowing out during routing. It's 3/4" material, which can be cut in a single pass on my machine. Also did the cutout in conventional direction, which leaves a nice finish on the cut during cutouts.
Steve Godding
Not all who wander (or wonder) are lost
Not all who wander (or wonder) are lost
- Creation in Wood
- Vectric Wizard
- Posts: 863
- Joined: Thu May 28, 2015 8:58 pm
- Model of CNC Machine: Legacy Maverick ATC 4x8 CNC
- Location: Monument, Colorado USA