My wife likes to play the puzzle at the local Cracker Barrel while waiting to be served. I looked at the rather plain wood block and said "I can make something that looks better than that for you to play at home".
My golf tees look a bit different, the corners and top edges are rounded, and there is a weave pattern on it. I used 2" powder coated deck screws and ground the points flat on a disk sander. The holes are 3/16" diameter and 5/8" deep. I made four blocks in a 16" long piece of red oak scrap.
She likes it a lot. So do three friends that got the other three.
CarveOne
Triangle Peg Board Puzzle
- mtylerfl
- Vectric Archimage
- Posts: 5865
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Triangle Peg Board Puzzle
Great idea and a stylish improvement too!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Wizard
- Posts: 1479
- Joined: Sun Nov 28, 2010 5:10 pm
- Model of CNC Machine: Home built designs - 3'x4' and 5'x12'
- Location: Eastern NC, USA
Re: Triangle Peg Board Puzzle
Thanks Michael,
One of the ladies in the local rifle club asked if I would make one for her that is set up for .223 REM dummy rounds. "No problem, just change the holes to 1/4" diameter."
CarveOne
One of the ladies in the local rifle club asked if I would make one for her that is set up for .223 REM dummy rounds. "No problem, just change the holes to 1/4" diameter."
CarveOne
CarveOne
http://www.carveonecncwoodcraft.com
http://www.carveonecncwoodcraft.com
- martin54
- Vectric Archimage
- Posts: 7339
- Joined: Fri Nov 09, 2012 2:12 pm
- Model of CNC Machine: Gerber 48, Triac PC, Isel fixed gantry
- Location: Kirkcaldy, Scotland
Re: Triangle Peg Board Puzzle
Looks good to me & I bet there are loads of other sports/activities that have something you could use as pegs, like you say just a case of scaling the holes to suit
-
- Vectric Wizard
- Posts: 1479
- Joined: Sun Nov 28, 2010 5:10 pm
- Model of CNC Machine: Home built designs - 3'x4' and 5'x12'
- Location: Eastern NC, USA
Re: Triangle Peg Board Puzzle
I cut four more today with the 1/4" holes. That is about the largest that can be used on this size peg board. For larger holes the weave shape vector and vector spacings can be modified to make a thinner weave pattern to open up the space in the weave, or just scale the whole design up to a slightly larger size to make room for a larger hole.
I should have a new photo to post sometime late afternoon tomorrow. It will show live cartridges in place only because I"m waiting for a friend to bring the dummy rounds. He will get one of this batch for his help.
CarveOne
I should have a new photo to post sometime late afternoon tomorrow. It will show live cartridges in place only because I"m waiting for a friend to bring the dummy rounds. He will get one of this batch for his help.
CarveOne
CarveOne
http://www.carveonecncwoodcraft.com
http://www.carveonecncwoodcraft.com
- mtylerfl
- Vectric Archimage
- Posts: 5865
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: Triangle Peg Board Puzzle
That is gonna be cool!CarveOne wrote:I cut four more today with the 1/4" holes. That is about the largest that can be used on this size peg board. For larger holes the weave shape vector and vector spacings can be modified to make a thinner weave pattern to open up the space in the weave, or just scale the whole design up to a slightly larger size to make room for a larger hole.
I should have a new photo to post sometime late afternoon tomorrow. It will show live cartridges in place only because I"m waiting for a friend to bring the dummy rounds. He will get one of this batch for his help.
CarveOne
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Wizard
- Posts: 1479
- Joined: Sun Nov 28, 2010 5:10 pm
- Model of CNC Machine: Home built designs - 3'x4' and 5'x12'
- Location: Eastern NC, USA
Re: Triangle Peg Board Puzzle
I managed to finish this sooner than expected today, so here is the result.
When looking for variants of this game board I found one that looks like a pizza slice. No doubt that we can come up with many more variants than what iis already out there.
CarveOne
When looking for variants of this game board I found one that looks like a pizza slice. No doubt that we can come up with many more variants than what iis already out there.
CarveOne
CarveOne
http://www.carveonecncwoodcraft.com
http://www.carveonecncwoodcraft.com
- dhellew2
- Vectric Wizard
- Posts: 1322
- Joined: Thu May 22, 2008 10:14 pm
- Model of CNC Machine: Legacy Artisan 72 and AVID CNC Rotary
- Location: Royal City Washington
Re: Triangle Peg Board Puzzle
Uses axel pegs [or anything that will fit in a 1/4" hole]
Dale
You will get old if you live long enough!
Young = time, no money
Old = money, no time
Dale
Young = time, no money
Old = money, no time
Dale
-
- Vectric Wizard
- Posts: 1479
- Joined: Sun Nov 28, 2010 5:10 pm
- Model of CNC Machine: Home built designs - 3'x4' and 5'x12'
- Location: Eastern NC, USA
Re: Triangle Peg Board Puzzle
Why, that is an udderly precious design Dale.
Thsnks for showing it here. I am surprised at how popular this game is.
CarveOne
Thsnks for showing it here. I am surprised at how popular this game is.
CarveOne
CarveOne
http://www.carveonecncwoodcraft.com
http://www.carveonecncwoodcraft.com
-
- Vectric Wizard
- Posts: 1479
- Joined: Sun Nov 28, 2010 5:10 pm
- Model of CNC Machine: Home built designs - 3'x4' and 5'x12'
- Location: Eastern NC, USA
Re: Triangle Peg Board Puzzle
Thank you Vectric for showcasing this simple game. Mine are used as gifts to friends and family.
CarveOne
CarveOne
CarveOne
http://www.carveonecncwoodcraft.com
http://www.carveonecncwoodcraft.com