Hi S.D.,
in mach3, to change the direction of an axis, click on the mach3 screen top left-
config,
homing/limits,
select the axis you want to change direction,
click column under reversed, hit ok,
you should be good to go!
Glenn
Finish Pass Issues
Moderator: Todd Bailey
-
- Vectric Craftsman
- Posts: 135
- Joined: Tue Jun 05, 2012 12:45 am
- Model of CNC Machine: Zenbot 2448
- Location: Belpre Ohio
Re: Finish Pass Issues
Hello SD.SimplyDifferent wrote:I am using Mach3. The machine is one I built and am trying to learn to use it properly. I have run lathes, milling machines and shapers quite a bit but not CNC. The software is a huge learning curve for me. I might have an MBA but this stuff is new to me. Many moons ago I took a class on NC machines, but that was the limit of my exposure. Most of the machine I have run since are computer controlled but are completely different than these machines.
The router is a new router with just about 6 or 8 test cuts on it. I would not doubt that I have something set up wrong in Mach3 as my Y axis is opposite of the arrow keys on my keyboard. Standing at the end of my machine facing it, the up arrow moves the Y axis to the right and the down arrow moves it to the left. My computer and keyboard are on a desk to the right of the machine, so I would think the up arrow would go to the left, away from me. It is just the opposite.
All of my cuts are opposite of what I think the orientation should be. Thanks to everyone's input, I have solved the issue of the finish pass not cleaning up the rough marks. I will attempt another of the jumping bass to see if I have it correct too. I will post the results Wednesday evening.
Thanks to all!!!!
I hope you trouble has be resolved by now, but if not I will make a hint. I am not an expert at Mach 3 but what you wrote about axis travel being reverse from your arrow keys and the cut image being flipped leads me to think you may want to look at your motor configurations. Mach 3 (CONFIG - PORTS AND PINS - MOTOR OUTPUTS - Dir LowActive) Just something easy to check if it helps that's great if not it only takes a moment to look.
Bill
-
- Posts: 28
- Joined: Sun Jan 13, 2013 11:52 pm
- Model of CNC Machine: Homebuilt
Re: Finish Pass Issues
I re-ran the tool path and followed the advise I have read here. I have a good cut with the exception that it is still flipped opposite of what I want. I will continue to see what I have wrong in Mach3 since this is where the issue has to be. I also noticed that when I cut out the attached model it is slightly oval rather the round. Again, it has to be a Mach3 setting.
Thanks goes to all of you!
Thanks goes to all of you!
- esteeme1
- Vectric Wizard
- Posts: 2132
- Joined: Tue Nov 02, 2010 3:26 pm
- Model of CNC Machine: Cobra 404 ATC; ROMAX WD-1; Shark
- Location: Chesapeake VA
- Contact:
Re: Finish Pass Issues
SimplyDifferent wrote:I re-ran the tool path and followed the advise I have read here. I have a good cut with the exception that it is still flipped opposite of what I want. I will continue to see what I have wrong in Mach3 since this is where the issue has to be. I also noticed that when I cut out the attached model it is slightly oval rather the round. Again, it has to be a Mach3 setting.
Thanks goes to all of you!
I think you will need to save the configuration after you make changes go to the Artsoft page and follow the tutorial. He will cover everything you need to know. as far as configuring your pins and tuning your motors. You will be glad you did.
http://www.machsupport.com/videos/
Jim Darlas
"Can Do!"
http://www.esteemedwoodcrafts.com/
http://www.esteemedplaques.com/
"Can Do!"
http://www.esteemedwoodcrafts.com/
http://www.esteemedplaques.com/