Just off the machine. Home Depot Poplar. There was some wood movement during the cutting since this is the rainy season in Northern California.
The heart-shaped one is just simple V-Carving.
The other two use a piece of clip art from Design & Make.
A few Children's Plaques
- Rcnewcomb
- Vectric Archimage
- Posts: 5928
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
A few Children's Plaques
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: A few Children's Plaques
Nice. Know what you mean about moisture and wood movement with our humid weather here in Southeast Georgia - although we're having colder temps at this time. Looking at those I also see that they could be made into boxes as well as plaques. Thank you for sharing.
- mtylerfl
- Vectric Archimage
- Posts: 5896
- Joined: Thu Jan 29, 2009 3:54 am
- Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
- Location: Brunswick, GA
Re: A few Children's Plaques
Those are very nice, Randall!
Hey, Dan. It’s only 36 degrees this morning in Brunswick, GA. The wind makes it feel a LOT colder! I can’t wait for Spring and Summer!!
Well, at least my workshop is a comfy 76 degrees. Might spend most of the day there!
Hey, Dan. It’s only 36 degrees this morning in Brunswick, GA. The wind makes it feel a LOT colder! I can’t wait for Spring and Summer!!
Well, at least my workshop is a comfy 76 degrees. Might spend most of the day there!
Michael Tyler
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
facebook.com/carvebuddy
-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: A few Children's Plaques
Michael, we're still sitting at around 33 degrees. I looked and Randall was at around 43 degrees at 6 this morning. My shop isn't fully finished and is still cold. I'm too cheap to buy a supplemental heater for it.
- Todd Bailey
- Vectric Staff
- Posts: 625
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Re: A few Children's Plaques
Always love the idea of plaques and gifts for new arrivals! Well done.
Really like both options. The raised VCarving is super nice... and the recessed blocks adds even more dimension!
Thanks, Randy for sharing!
Really like both options. The raised VCarving is super nice... and the recessed blocks adds even more dimension!
Thanks, Randy for sharing!
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com
- Rcnewcomb
- Vectric Archimage
- Posts: 5928
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: A few Children's Plaques
Glazing in process:
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
- Todd Bailey
- Vectric Staff
- Posts: 625
- Joined: Mon Nov 24, 2014 8:40 pm
- Model of CNC Machine: CraftCNC
- Contact:
Re: A few Children's Plaques
Randy...
Looks good! Love that finish. Well Done.
Looks good! Love that finish. Well Done.
------------------------------------
Todd Bailey | Design and Make
DesignAndMake.com
Todd Bailey | Design and Make
DesignAndMake.com