Any ideas ?
-
- Vectric Wizard
- Posts: 493
- Joined: Sat Jun 11, 2011 3:27 pm
- Model of CNC Machine: Probotix Meteor 25 x 50
- Location: Jefferson City, Mo.
Any ideas ?
Thanks guys.
Dave
- Rcnewcomb
- Vectric Archimage
- Posts: 5911
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Any ideas ?
Are these decorative or does the finish need to be food-safe?
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Wizard
- Posts: 493
- Joined: Sat Jun 11, 2011 3:27 pm
- Model of CNC Machine: Probotix Meteor 25 x 50
- Location: Jefferson City, Mo.
Re: Any ideas ?
They need to be food safe Randall, that's why I'm stuck and asking.
Dave
Dave
-
- Vectric Craftsman
- Posts: 125
- Joined: Wed Jan 04, 2012 3:50 pm
- Model of CNC Machine: Shark
- Location: MN
Re: Any ideas ?
General Finishes makes a salad bowl finish that is non-toxic when cured. I use it when working with items that are going to come into contact with food. If you are wanting to use the paint and sand method I would still finish the wood with the salad bowl finish first. Bamboo is pretty porous and you probably will get some paint bleed up the pores if you don't seal the v carve first. If it was my project and I wanted color I would seal with a couple coats of salad bowl finish, paint with an acrylic hobbyist paint, sand any mistakes outside the lines, then a couple more coats of salad bowl finish. Personally I think just a couple coats of a non-toxic finish should give you enough contrast. If you use this method you still can make that call after the first two coats of salad bowl finish.
Mother Nature always bats last!
-
- Vectric Wizard
- Posts: 493
- Joined: Sat Jun 11, 2011 3:27 pm
- Model of CNC Machine: Probotix Meteor 25 x 50
- Location: Jefferson City, Mo.
Re: Any ideas ?
I will give salad bowl finish a try. Thanks for the suggestion.
Dave
Dave
- Rcnewcomb
- Vectric Archimage
- Posts: 5911
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Any ideas ?
You can make food-safe dyes using coffee or tea. ->e-how article
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Wizard
- Posts: 722
- Joined: Sun Jun 16, 2013 4:40 am
- Model of CNC Machine: Home Built 4-axis Router
- Location: Fort Collins, CO
Re: Any ideas ?
You could torch the carving (lightly) with a narrow flame and then sand the flat surface over before finishing with oil.
That said, having a carving on a pizza paddle dusted with flour (to smoothly slide off the limp dough) will not exactly improve usability.
The flour and overflow tomato sauce will get stuck in the carving or the dough may catch. I usually have to brush off my (uncarved) pizza paddle under running water after use.
A vcarve inlay might be better.
That said, having a carving on a pizza paddle dusted with flour (to smoothly slide off the limp dough) will not exactly improve usability.
The flour and overflow tomato sauce will get stuck in the carving or the dough may catch. I usually have to brush off my (uncarved) pizza paddle under running water after use.
A vcarve inlay might be better.
-
- Vectric Wizard
- Posts: 722
- Joined: Sun Jun 16, 2013 4:40 am
- Model of CNC Machine: Home Built 4-axis Router
- Location: Fort Collins, CO
Re: Any ideas ?
Can not really confirm that. While I used bamboo plywood mostly for more practical things like furniture, I tried a few experimental v-carvings just to see how it came out. The dragon below is in natural color vertical set bamboo plywood (your paddle is similar but horizontally set strips) with simple black spray paint filling and the other one is in marbled compressed bamboo (floor panels) with gold spray paint. I did not see much bleeding if any in either experiment. IIRC I did not seal the surfaces before filling the carving.lsvien wrote:..... Bamboo is pretty porous and you probably will get some paint bleed up the pores if you don't seal the v carve first.....
- rscrawford
- Vectric Wizard
- Posts: 1103
- Joined: Mon Jan 17, 2011 6:49 pm
- Model of CNC Machine: CAMaster Cobra 408 ATC, ShopSabre IS408
- Location: Wetaskiwin, Alberta
- Contact:
Re: Any ideas ?
Most finishes are food safe once they are fully polymerized or 'dry'.
If the bamboo was prefinished before you carved into it, you could use an aniline dye to colour the v-carve, then apply an oil finish. Pure tung oil is completely food safe even before it polymerizes (but does take a long time to polymerize, at least a week per coat).
If the bamboo was prefinished before you carved into it, you could use an aniline dye to colour the v-carve, then apply an oil finish. Pure tung oil is completely food safe even before it polymerizes (but does take a long time to polymerize, at least a week per coat).
Russell Crawford
http://www.cherryleaf-rustle.com
http://www.cherryleaf-rustle.com
-
- Vectric Wizard
- Posts: 520
- Joined: Sun May 03, 2015 12:25 pm
- Model of CNC Machine: Axiom AR8
- Location: Savannah, GA
Re: Any ideas ?
One of the things you will have to consider is cleaning the peel especially with the carving in it. I would go with pure tung oil which doesn't have additives in it and can provide good protection including some water protection. I make some pieces for a microbrewery to hold glasses of their various brews and they have to put their boards in a dishwasher. They recoat them with pure tung oil after about 3 washings. But their boards go through a much tougher use than yours would unless you are making those for a pizza shop.
- SteveNelson46
- Vectric Wizard
- Posts: 2304
- Joined: Wed Jan 04, 2012 2:43 pm
- Model of CNC Machine: Camaster Stinger 1
- Location: Tucson, Az.
Re: Any ideas ?
For durability, there isn't any finish that is as good as polyurethane. Like Russel stated, after it is polymerized most finishes are food safe.
I made some "flight trays" awhile back and used polyurethane for a finish. However, they don't put them in a dishwasher and I wouldn't recommend anything made out of wood to be placed in one.
I made some "flight trays" awhile back and used polyurethane for a finish. However, they don't put them in a dishwasher and I wouldn't recommend anything made out of wood to be placed in one.
Steve
-
- Vectric Wizard
- Posts: 493
- Joined: Sat Jun 11, 2011 3:27 pm
- Model of CNC Machine: Probotix Meteor 25 x 50
- Location: Jefferson City, Mo.
Re: Any ideas ?
Thanks all. I decided to do bowl oil and it showed up great. Always get the right answers here. Thank you. It is for a pizza shop, and I figure they could always use the back side and hang the front side out.
Dave
Dave