" Oh la vache !!! "
" Oh la vache !!! "
Bonjour
Un petit post en FRENCH pour partager un peu... Sous VCARVEPRO4.6. Bois utilisé chêne...
http://www.sculpture-en-bois.fr/
A noté quelques difficultés rencontrées pour l'usinage du contour de la vache sous cette version. Pas de possibilité pour réaliser un parcours d'outil à un écart paramétré du contour du dessin. Obligation de créer ce contour sous photoshop. Peut être possibilité sous les dernières versions???
Un petit post en FRENCH pour partager un peu... Sous VCARVEPRO4.6. Bois utilisé chêne...
http://www.sculpture-en-bois.fr/
A noté quelques difficultés rencontrées pour l'usinage du contour de la vache sous cette version. Pas de possibilité pour réaliser un parcours d'outil à un écart paramétré du contour du dessin. Obligation de créer ce contour sous photoshop. Peut être possibilité sous les dernières versions???
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: " Oh la vache !!! "
Nice clean design.
To clean up some of the edge issues try using the Curve Fit tool under Edit Object. Most of the time when importing vectors I've found there are way too may nodes and this will effect the smoothness of the carving.
I'm not sure what edit options are available under VCP4.6, but here's a few suggestions to look at if available.
As far as the creations of the offset outline around the cow try the Offset tool under Offsets and Layout (If I translated your comments correctly). The oval is also a simple issue in VCP
To clean up some of the edge issues try using the Curve Fit tool under Edit Object. Most of the time when importing vectors I've found there are way too may nodes and this will effect the smoothness of the carving.
I'm not sure what edit options are available under VCP4.6, but here's a few suggestions to look at if available.
As far as the creations of the offset outline around the cow try the Offset tool under Offsets and Layout (If I translated your comments correctly). The oval is also a simple issue in VCP
John
Maker of Chips
Maker of Chips
-
- Vectric Wizard
- Posts: 1012
- Joined: Fri May 15, 2015 1:10 pm
- Model of CNC Machine: 3 axis small size machine
- Location: France
Re: " Oh la vache !!! "
Bonjour,
Réalisation sympathique. Je ne suis pas la gamme Vectric depuis assez longtemps pour connaître les fonctions de la V4. Ce qui est sûr c'est que la fonction est disponible depuis plusieurs versions. Il est possible de télécharger la démo pour la tester. L'écart entre une version 4 et une version 9 justifie très probablement la mise à jour. En revanche, il faut faire attention, il y a maintenant 2 versions de Vcarve (pro et desktop) avec des fonctionnalités plus ou moins avancées. Voir le comparatif des fonctions disponibles sur le site de Vectric.
Réalisation sympathique. Je ne suis pas la gamme Vectric depuis assez longtemps pour connaître les fonctions de la V4. Ce qui est sûr c'est que la fonction est disponible depuis plusieurs versions. Il est possible de télécharger la démo pour la tester. L'écart entre une version 4 et une version 9 justifie très probablement la mise à jour. En revanche, il faut faire attention, il y a maintenant 2 versions de Vcarve (pro et desktop) avec des fonctionnalités plus ou moins avancées. Voir le comparatif des fonctions disponibles sur le site de Vectric.
Best regards
Didier
W7 - Aspire 8.517
Didier
W7 - Aspire 8.517
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
Re: " Oh la vache !!! "
That is one nice piece of work. Simple and to the point.
Clean but full and nice placing of the elements.
I hate to say this ( I may be the only one) but there is 1 flower I would have put
someplace else. LoL
Don
Clean but full and nice placing of the elements.
I hate to say this ( I may be the only one) but there is 1 flower I would have put
someplace else. LoL
Don
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
Re: " Oh la vache !!! "
I was going to just leave that one aloneMakingtoothpicks wrote: I hate to say this ( I may be the only one) but there is 1 flower I would have put
someplace else. LoL
Don
John
Maker of Chips
Maker of Chips
Re: " Oh la vache !!! "
Je vous remercie de vos réponses. Oui il va falloir que j'investisse dans la nouvelle version de VCARVEPRO. Car j'ai de plus en plus de besoins particuliers sur des photos ou des logos.
Ci dessous réalisation d'un chalet en bois sous PHOTOVCARVE. Réalisation sur une planche de noyer résultat sympa...
https://www.facebook.com/artisa-numcom-127787383931488/
Ci dessous réalisation d'un chalet en bois sous PHOTOVCARVE. Réalisation sur une planche de noyer résultat sympa...
https://www.facebook.com/artisa-numcom-127787383931488/
-
- Vectric Wizard
- Posts: 1012
- Joined: Fri May 15, 2015 1:10 pm
- Model of CNC Machine: 3 axis small size machine
- Location: France
Re: " Oh la vache !!! "
Translation:jejeadx wrote:Je vous remercie de vos réponses. Oui il va falloir que j'investisse dans la nouvelle version de VCARVEPRO. Car j'ai de plus en plus de besoins particuliers sur des photos ou des logos.
Ci dessous réalisation d'un chalet en bois sous PHOTOVCARVE. Réalisation sur une planche de noyer résultat sympa...
https://www.facebook.com/artisa-numcom-127787383931488/
Thank you all for your replies. Yes I'm going to upgrade to Vcarve Pro. I have more and more specific needs for photos or logos. Here is a log house made with Photocarve. Nice result with a walnut board.
Best regards
Didier
W7 - Aspire 8.517
Didier
W7 - Aspire 8.517
-
- Vectric Wizard
- Posts: 519
- Joined: Tue Jul 21, 2009 8:22 pm
- Model of CNC Machine: ShopBot Buddy Standard
- Location: Marietta, GA.
Re: " Oh la vache !!! "
Very nice...joe
- scottp55
- Vectric Wizard
- Posts: 4713
- Joined: Thu May 09, 2013 11:30 am
- Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
- Location: Kennebunkport, Maine, US
Re: " Oh la vache !!! "
LOVE the detail and overall effect on that Cabin!!
Cringe on the cutting time with all the Z moves:)
Well done!
scott
Cringe on the cutting time with all the Z moves:)
Well done!
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.
R.N.
- FixitMike
- Vectric Wizard
- Posts: 2173
- Joined: Sun Apr 17, 2011 5:21 am
- Model of CNC Machine: Shark Pro Plus (retired)
- Location: Burien, WA USA
Re: " Oh la vache !!! "
Love the cow. You could add a bit of visual interest by moving one of the flowers so it is partially outside of the oval.
Good judgement comes from experience.
Experience comes from bad judgement.
Experience comes from bad judgement.
-
- Vectric Craftsman
- Posts: 186
- Joined: Fri Apr 04, 2014 2:21 am
- Model of CNC Machine: Axiom AR4Pro+ and AR8Pro+
- Location: Edmonton, Alberta, Canada
Re: " Oh la vache !!! "
France + VIN = passion. Attention no automatic translation for the curious.