Page 1 of 10

Guitars - Vectric - Alex Navarro

PostPosted: Thu Aug 25, 2011 12:54 am
by Alex Navarro
Acquired my Vcarve and I'm starting to do my guitar work on it now.
I made this video with my first steps with experiments.
Next week will put the results in videos on machine.

Thanks

Alex

http://www.youtube.com/watch?v=N_f-eoJFJu0

Re: Guitars - Vectric - Alex Navarro

PostPosted: Thu Aug 25, 2011 6:37 am
by Mogal
Thank you,
I'll be watching with interest!

Re: Guitars - Vectric - Alex Navarro

PostPosted: Tue Nov 29, 2011 5:54 pm
by Alex Navarro
Mogal wrote:Thank you,
I'll be watching with interest!


Hi

I'm doing with my guitars Vcarve Pro + Cut3D for some customers.
It is more difficult than the Aspire by some limitations, but it's still an excellent software and recommend.

Below 4 videos with their simulations.


http://www.youtube.com/watch?v=bZJvn5UC-a8

http://www.youtube.com/watch?v=0-86LWDZcKA

http://www.youtube.com/watch?v=jfqdar-pQ0c

http://www.youtube.com/watch?v=tZQH9EuxFeo

Re: Guitars - Vectric - Alex Navarro

PostPosted: Thu Dec 29, 2011 12:22 am
by Alex Navarro
Some new works

Re: Guitars - Vectric - Alex Navarro

PostPosted: Thu Dec 29, 2011 6:58 pm
by Alex Navarro
Alex Navarro wrote:Some new works


Now the body

Soon I´ll send the simulations

Re: Guitars - Vectric - Alex Navarro

PostPosted: Thu Dec 29, 2011 7:21 pm
by mezalick
Nice work Alex.
Grande artesanato!

Michael

Re: Guitars - Vectric - Alex Navarro

PostPosted: Thu Dec 29, 2011 7:25 pm
by fretsman68
Hi Alex,

What methods are you using to do the belly and forearm cuts?

Will you be attempting to do archtops?

Dave

Re: Guitars - Vectric - Alex Navarro

PostPosted: Fri Dec 30, 2011 9:03 pm
by Alex Navarro
fretsman68 wrote:Hi Alex,

What methods are you using to do the belly and forearm cuts?

Will you be attempting to do archtops?

Dave


Hi Dave
I use to 3d forms the Rhinoceros and so imported into vectric softwares.

I make top shapes like a this image attached. Is possible to make the soft body (front and back) in Aspire with too rails sweep.

Rhinoceros + Cut3d and Vcarve are very nice for instruments makers. sure that Aspire is more complete and you can make a same work if you learn good the reliefs tools

Re: Guitars - Vectric - Alex Navarro

PostPosted: Fri Dec 30, 2011 10:10 pm
by fretsman68
Oh, I see, thought these were done with VCarve, thanks for clearing that up!

Dave

Re: Guitars - Vectric - Alex Navarro

PostPosted: Fri Dec 30, 2011 10:14 pm
by Alex Navarro

Re: Guitars - Vectric - Alex Navarro

PostPosted: Sat Dec 31, 2011 1:50 am
by Alex Navarro
fretsman68 wrote:Oh, I see, thought these were done with VCarve, thanks for clearing that up!

Dave


:D

Re: Guitars - Vectric - Alex Navarro

PostPosted: Sat Dec 31, 2011 10:48 am
by Alex Navarro
Alex Navarro wrote:
fretsman68 wrote:Oh, I see, thought these were done with VCarve, thanks for clearing that up!

Dave


:D


Hi Dave, this idea occurred to me to make shapes or soft top.
Take the video and see if that helps something.

http://youtu.be/BS1vWKdlIBs

Re: Guitars - Vectric - Alex Navarro

PostPosted: Sat Dec 31, 2011 11:04 am
by Alex Navarro

Re: Guitars - Vectric - Alex Navarro

PostPosted: Sat Dec 31, 2011 11:35 am
by Alex Navarro
File

Re: Guitars - Vectric - Alex Navarro

PostPosted: Sat Dec 31, 2011 12:58 pm
by Alex Navarro