Best Practices for Productivity as an Independent Craftsman

Best Practices for Productivity as an Independent Craftsman

Postby Rcnewcomb » Fri Apr 07, 2017 10:15 pm

Not exactly a hardware topic, but I wanted to put this out there for discussion.

Below is an article by Eric Schaefer regarding his 15 Best Practices for Productivity as an Independent Craftsman.

In addition to the ones he mentions, another one I dscovered was, "Just because you are in the shop doesn't mean you are productive". I my case, unless I'm on a roll, I wasn't productive after 11 hours straight. I tended to make more errors or make poor decisions. It was better to take a break.

Read the article and offer some of your tips for Productivity as an Independent Craftsman.

My 15 Best Practices for Productivity as an Independent Craftsman
by Eric Schaefer

Introduction
Minimizing distractions and being productive is something everyone struggles with. Just because I’ve written this article, that doesn’t mean that I’ve mastered productivity. Far from it. It is a daily struggle. Anyone who is honest will likely tell you the same thing. My goal here isn’t to list off generic productivity tips for all entrepreneurs. There is enough of that already. The internet doesn’t need anymore! Seriously. Rather, I want to share some of the practices that have worked well for me as a luthier and as a solopreneur.

As you read these, you might be thinking, “Wow, this guy really has his s#!% together!” I want to be as straightforward as possible and I want the reader to understand that I do not follow all of these practices all of the time. In fact, I don’t even follow half of these practices half of the time! I wish I did, but I am simply too human. It takes a lot of discipline to establish a new habit and only a little bit of complacency for that habit to slip away. All of these practices taken together will seem extreme, even draconian. The point is to consider each separately and incorporate into your life what makes sense for you. Do not attempt them all at once. You will burn out! It is much more practical to challenge yourself with establishing just 1 or 2 new habits. And of course, not everything that works for me, works for you. We are all different.

Disconnect from the Internet
I’m sure that some of you can relate to this:

You wake up in the morning and the first thing that you do is look at your phone or flip open your laptop. Without thought or intention, like a trained monkey, you are looking for notifications.

“Did that client e-mail me back?,” “I wonder if anybody commented on my facebook post?,” “How many likes did it get?,” “Oh look, Eric Schaefer posted a new video!,” “New superfood discovered in Peruvian rainforest… well I have to read that!” … An hour later, you’ve gotten zero work done and you are angrily posting a Facebook status that you are sure will change the way people think about politics.

In fact, there is a very good chance that some of you will have arrived at this article through a similar chain of events. If that is the case, then stop reading! Bookmark this page for later and get back to work! You are wasting time!

Peeking at your notifications is absolutely the worst thing you can do in the morning, even for those of us who are disciplined enough to avoid time-wasting sites like Facebook.

In fact, I personally, don’t care about what is happening on Facebook. But the morning e-mail trap is just as bad, if not worse. I will habitually check my phone for new e-mails the moment I wake up, if I can. This sets in motion a reactionary cycle where I am not working on the tasks that I consider to be the most urgent or important. Rather, I spend time that I don’t have on other people’s agendas. This is a particularly insidious trap, because it’s easy to justify to yourself that you are being responsible and getting work done, because they are, after all, client emails.

It’s not that these e-mails aren’t important. They are important, but they can certainly wait. The idea is to be intentional about your workflow rather than reactionary. Starting your day with e-mails forces you into a reactionary workflow.

This may seem extreme to some, but every night before I go to bed, I literally disconnect the internet. I pull the plug on the router. I also switch my phone to “Ultra Power Saving Mode.” This is a function on an Android phone that saves power with a simple home screen and access to a limited number of apps: Phone, Text messaging and the clock. That’s it! This is perfect for me because I need to be accessible by phone throughout the day. As many of my students know, that is the best way to reach me.

I do this before I go to bed so I don’t have to rely on my mental fortitude to disconnect when I wake up in the morning, when my willpower is at it’s weakest!

Depending on what I have planned for the day I will either leave it off all day or I will turn it on when I need it. The point, however, is that I atleast start my day on my terms, to work on the projects that are most important to me. I am not at the whim of everybody else’s notifications.

With all that said, I am actually very pro-social media. I manage my own wordpress site with a blog, an online guitar building course and a private forum. I also manage my own youtube channel, Facebook page and instagram. I love what the internet and social media allow us to do. But it can only benefit us if we are intentional with how we use it.

For me, the key to being intentional about how I use the internet is to set up my devices with certain controls or applications that manage distractions. That way, even after I’ve plugged the router in for the day, I am less likely to be pulled off task by something online.

Here are some of those controls:
- I listen to alot of podcasts while I’m working on guitars. I avoid having to go online to find new episodes by setting up my itunes to automatically download new episodes from podcasts that I am subscribed to. That way, I don’t have to open my browser in the first place.
- As amateur and even professional luthiers we constantly have “How To” questions that we want answered, and it would be silly to deny ourselves of the virtually boundless resource that we have at our fingertips. However, when you open up a search page on almost any browser you see a list of your most visited sites, which for me are gmail, youtube and facebook. It is very tempting when I am on that page to either check my inbox, or check for youtube or facebook comments. I remove the temptation by using a Chrome extension called “New Tab Redirect.” This removes the most visited sites, so that all you see is a blank search bar.
- Finally, I use another extension called “StayFocusd.” This extension allows you to set limits to the amount of time that you spend on certain sites. That way, if I need to go on sites like Facebook or Youtube to post a new video or to answer questions, I won’t get pulled down into the social media rabbit hole, or atleast not for long!

Assign all of your marketing/sales/accounting work to one or two days of the week
As craftsmen we tend to loath the idea of marketing our products or services. We’d much rather spend our time in the shop. We are artists firsts and unfortunately artists tend to look down on business as a necessary evil. This is unfortunate because that line of thinking is flawed in so many ways. If you suffer from this belief then, honestly, you should not be in business for yourself, just as a matter of practicality. Get a job and let someone else deal with the “evil” side.

I have a healthy view of marketing and sales but I still don’t particularly enjoy doing it. As solopreneurs we must wear many hats and some of those hats are not very comfortable. Switching from hand carving a neck to working at a cold laptop is a rough transition and I’d personally rather get all my laptop work done on Monday and then be able to devote my full attention to building and repairing instruments for the rest of the week. I call it Marketing Monday!

Establish a price range with clients ASAP
I struggled with this for the longest time. Consider this scenario:

A customer e-mails you with a question about a custom instrument or a repair. Customer asks, “Can you build a blankety blank with blank?”

You respond with a well thought-out explanation of why blankety blanks are incompatible with blank, complete with graphs of the density of blank.

Customer insists that his father’s brother’s nephew’s cousin’s former roommate owns a blankety blank with blank, and that there must be a way to build a blankety blank with blank.

You respond by politely reaffirming that blankety blanks are incompatible with blank in a way that dodges the implication that his father’s brother’s nephew’s cousin’s former roommate’s credibility is in any way suspect.

Customer concedes that maybe some blankety blanks are incompatible with certain varieties of blank.

You respond with more graphs, and links to peer-reviewed scientific journals, and a gentle suggestion that perhaps he would be interested in a blank with a blank instead.

Customer gets excited by the suggestion. “Oh, what about two blanks with a blank!”

You respond with a lengthy explanation of why two blanks is also incompatible with blank.

Customer is somewhat deflated but still determined to invest in blank. Customer asks, “How much do you charge for a blank with a blank?”

You respond, “Work on blanks is in the range of $2000 – $2500.”

Silence. End of conversation.

Now consider the same scenario with a different approach:

A customer e-mails you with a question about a custom instrument or a repair. Customer asks, “Can you build a blankety blank with blank?”

You respond, “A blank with a blank is a better alternative and I can explain why if you want me to. By the way, work on blanks is in the range of $2000 – $2500.

Silence. End of conversation.

Now both scenarios had the same end result: the customer wasn’t interested because of the price point. In the first scenario, you spent hours or maybe even days answering emails and researching the possibilities of the project or repair. In the second scenario, you responded in less than a minute with the price point in the email. Which approach is more productive? The second scenario saved your time and the customer’s time.

In both scenarios I was being a little bit tongue-in-cheek and poking fun at the customer, and you may have gotten the impression that the customer was somehow wrong or at fault, or that the customer was the one who wasted time. And it is easy in the moment to believe that and get frustrated at the customer. Remember this:

If you don’t establish the price range up front, then you are wasting your own time.

The customer does not know the current standard price of a custom instrument any more than you know the current standard price of plastic surgery (unless you’re a surgeon or a supermodel). As the professional, it is your job to establish the price up front.

Avoid academic procrastination
Regular couch-potato procrastination is easy enough to spot. You know when you are lounging about during work time and you feel guilty about it.

However, there are two forms of procrastination that I am going to talk about which are very subversive in the sense that they disguise themselves as productivity when they are in fact procrastination.

The first one I call academic procrastination. This is procrastination by learning. You believe that once you reach some critical threshold of knowledge, productivity and success will simply happen as a byproduct of sheer brilliance. People who suffer from this form of procrastination imagine that people who are productive and successful have reached this critical threshold and know everything. Otherwise, they wouldn’t be competent enough to even start.

I believe that this form of procrastination is not about laziness. It is about fear. The academic world of books and theories insulates you from the real world of failures and deadlines and criticism from peers. Nobody can judge you or claim that your venture was a failure if you never even start.

The worst part about this form of procrastination is that it discounts the most powerful form of learning: Experiential learning. That is, the knowledge you gain from doing.

I still allow time in my day-to-day for learning from teachers, books, videos and podcasts. There’s value in that. But only if you apply that knowledge as you gain it. The most effective education, in my opinion, is in alternating periods of academic learning with real-world application. Education should be viewed as ongoing and pervasive rather than as something you do before you can be productive.

Avoid perfectionism procrastination
Perfectionism procrastination is the other form of subversive procrastination. This one is especially tricky to spot because being a perfectionist is at the core of being a craftsman. Don’t get me wrong. Being a perfectionist is a good thing in lutherie. I consider myself to be one. I also, however, suffer from perfectionism procrastination, which is not a good thing.

Let me explain it this way:
I have realized that there is a finite amount of mental energy that I can devote to any one thing before I begin to lose interest. When I lose interest, the quality of my work suffers. This seems to be an inescapable fact. With that in mind, it makes sense to critically analyze the build process and determine where clear, focused energy is most needed, and to work with an efficiency mindset at the times when clear focused energy is less necessary.

I see the same thing in students who attend my courses. They begin the course with a full tank of mental energy and a high interest. As the energy wanes. the work suffers. The end result is that the student is more focused and detail oriented in the early and middle stages, and more rushed at the end. Fortunately, I’m there to push them when they need to be pushed in the early and middle stages so that they still have something in the tank when they get to the final stages of assembly and setup, where a detail-oriented mindset is more important.

The point is that there are points of the build process where a perfectionist’s mind is not necessary, and it is at those stages where the perfectionist risks not only wasting time, but even sacrificing the quality of their work further along in the process.

Use the Pomodoro technique
The Pomodoro Technique is a time management technique that involves breaking up a task into manageable 25 minute intervals of intense focus. Each interval is followed by a 5 minute break. Four intervals is considered a set and earns a longer 15 – 30 minute break. The idea is that there is no reasonable excuse to go off task when intervals are just 25 minutes. For example, even if you have to use the restroom, you can wait until the next break. If someone calls or interrupts, you can address it on the next break. When you first start the pomodoro technique, you will likely find yourself checking your phone or walking off to the bathroom during a Pomodoro out of habit. It’s important, however, to catch yourself and get back on focus once you recognize that you’ve strayed. After some time of practicing Pomodoro, however, staying on task will become more habitual.

I use this technique fairly often. When I’m having an off day, it helps to have a system like this to fall back on. Sometimes I use an app called Kanban Flow, and sometimes I use a simple kitchen timer.

Put away your tools after every job or at least at the end of the day
Nothing wastes time like a messy shop. It’s hard to even muster the motivation to work when your benchspace is crowded and your tools are not where they are supposed to be.

The best time to put tools away is immediately after the repair or the particular job (side bending, neck carving etc.) is complete. It is much more manageable then than it is 3 weeks later when every bare spot of bench is covered with tools. The next best time is at the end of the day before you close up. Atleast then, you can walk into a clutter free environment the next morning.

Personally, I still let my workshop become a mess from time to time. In the moment it seems more efficient to leave the tools out on the bench and simply get started with the next thing. However, everytime I do that, I come to the conclusion in hindsight, that I would have been far more productive if I took a minute to clear the bench between jobs.

Now be careful here! Because there is another form of procrastination lurking in a messy shop. That is procrastination by cleaning everything in sight! I’ve fallen for this trap before. It begins innocently enough by putting your tools away. Then maybe you shopvac all the bench space to clear the dust. Then you notice dust clinging to the window trim, so you vac that up as well. However, the windows look a bit streaky, so you break out the windex… stop! You are procrastinating again! You can make a note that the windows need cleaning and add it to your workflow later. There’s a good chance that you will look at the windows later and realize that they didn’t really need cleaning after all. You were just using the windows as an excuse to put off the work that really needs to get finished now.

Keep tools sharp
Not scary sharp. Just serviceably sharp. For those just getting started in woodworking, pay to have your chisels and plane irons sharpened by a professional just one time. That way, you can see what a sharp tool is like, so you can understand the value of a sharp tool when it comes to your time and the value of your work. And just so you know, a new tool is not a sharp tool. Not even close. If you just bought a shiny set of chisels, yes, even those need to be sharpened. It makes all the difference in your productivity, the quality of your craftsmanship and the satisfaction you get from woodworking.

Schedule regular “sharpening sessions,” where you take the time to sharpen all the tools that need sharpening. No need to get carried away and sharpen every tool you have. Just the ones that need it. I recommend the Worksharp 3000 for fast efficient sharpening.

Phone calls are less time consuming than email
This is one of those things that is true for me, but definitely not true for everyone. It really depends on your personality type. Some people are very efficient at answering e-mails. I, however, am not. I think long and hard about everything I am typing, but when I am on the phone with a client, the words just fall out. An answer that takes 30 minutes to write up in e-mail, could be a 5 minute phone conversation. And the best part about phone conversations is that the client can ask follow up questions and you can address those on the spot, whereas e-mail can become a long drawn out affair with weeks of back-and-forth dialogue.

I still answer plenty of e-mails. In fact, most of the time it is quicker to just fire back an e-mail for questions like “Is there still available in the October course?” However, if someone asks a question or several questions that I know requires an in-depth explanation and possibly will result in many follow-up questions, I explain that to the person and leave my number. Customers with hard questions are always delighted to see that I’ve given them the option for more personable communication through the phone.

Establish deadlines
This one is key. Many projects in lutherie don’t have a deadline imposed on them by someone else. For example, if you are building an instrument and that instrument is not for a specific client, then that project does not have a deadline unless you impose a deadline on that project. For some of you, this may sound like a good thing. Perhaps the whole reason that you got into lutherie and woodworking was to escape the world of arbitrary deadlines.

Just let this sink in:
Projects without a deadline don’t get finished and they are the biggest drain on your time.

You have to impose a deadline. If the project doesn’t seem important enough to have a deadline, then that is probably not a project that you need to be doing.

I use what I call the 10 X rule to schedule deadlines. That is, you estimate the time that you think it will take to complete a project, and then you times that by 10. And that is your deadline.

A deadline, in my opinion, need not be near term. It simply needs to exist. Being realistic and putting the deadline far into the future makes it more likely that you will stay true to deadlines.

Right now, you probably have half-finished projects collecting dust in your shop. I know that I have several! It is a good idea to make a list of those projects and impose a deadline on each one. If you feel a heavy resistance to imposing a deadline on any one project, then you should consider scrapping that one. It is a drain on your energy.

Prioritize tasks the night before
Prioritizing tasks and making a “to do list” the night before allows you to get into your workflow immediately in the morning. I don’t do this as often as I should, but when I do I have an immensely productive day. If I don’t do this the night before, I am at risk of starting my day by working on the tasks that are the easiest or the most satisfying in the moment. Unfortunately, the easy and fun tasks are never the most important ones! Kanban Flow, the same app that I use for the Pomodoro technique, is a great app for prioritizing tasks.

Start work immediately!
And that brings us to our next practice: getting started right away! I’ve tried all kinds of “morning routines” that “productive people” swear by: meditating, exercising, journaling, drinking kale smoothies etc… These are all things that get you into the “right mindset” to tackle what you need to do that day. And they do, honestly, have their merits.

But I have found for me, nothing beats simply rolling out of bed, pouring a glass of water and starting a Pomodoro (see Pomodoro technique above). I don’t take a shower, and I don’t eat breakfast… yet. These can wait. Meditation and exercise (if you’re into that) can also wait. Whatever morning routine that works for you, will feel so much better if you put it off until after you’ve gotten atleast 25 minutes of focused work done. That’s it! Anybody can work hard for just 25 minutes. Nothing gets you in the mood for having a productive day like checking something off your list first thing in the morning.

And if you really want to step it up do a whole set (4) of Pomodoros (~2 hrs of focused work). The most productive days I have start off this way. Waiting 2 hours to have breakfast isn’t always easy for me, so I don’t do this every day.

Once I’ve completed either one pomodoro or a whole set of pomodoros I can go through my morning routine (shower, breakfast, exercise, or whatever) without the anxiety of feeling like I’m wasting time.

I don’t have to commute to the shop. I live on-site. So this works especially well for me because I can simply wake up, walk down to the shop and get started. I understand that this is not the case for many people. However, there is always some work that you can do from home. Think about it. Maybe it’s posting photos of your work on your website or on social media. Just wake up 25 minutes earlier and get that done before going through your morning routine. It sets a great tone for the rest of the work day.

Be Consistent
Above all, be consistent! All of the above mentioned practices only work if you practice them with some level of consistency. So be very mindful of this from the outset. Consistency creates habit. Once a practice becomes habitual or second-nature, we spend less mental energy, or sometimes even physical energy, enforcing the practice. The mental resistance is no longer there. When you start a new habit, you are in the honeymoon phase of habit formation. This is where you are most inspired and determined. This may even give you the false impression that maintaining this habit is going to be easy. The key to making a habit stick is to be aware that the honeymoon phase of habit formation will end, as all honeymoons do. If you are aware of it, you can say to yourself, “This is easy now because I’m inspired, but the real test of willpower is coming.” That way, you will be ready when the honeymoon phase ends.

This is not to say that a habit is not worth forming if you can’t do it consistently forever! That is ridiculous. You can fall off the wagon. I fall off the wagon all the time. In fact, falling off the wagon is actually a good thing! “Nonsense!” you say. Oh, but it’s true! Falling off the wagon gives you the opportunity to develop the most important habit of all habits: Getting back on the wagon. When you fall off the wagon, rather than throwing your hands in the air in defeat, you can calmly and coolly commit to resuming your practice as if you never fell off in the first place. Don’t get flustered and scold yourself. Just get back on. Every iteration of Off-the-wagon On-the-wagon, further develops this habit that affects all other habits. If you are the type of person who logs your success in a journal, instead of tracking how many days you’ve done ____, try focusing on how many times you’ve fallen and gotten back on the wagon instead. See how much more effective that is in promoting longevity in your habits.

When in doubt, just do something
Sometimes a tool breaks or I realize that I ordered the wrong materials. It’s life. This happens. I made my “to do list” the night before, but now I can’t complete any of the items that I need to complete. Bummer…

On a good day, I will go back to the drawing board and come up with a new, revised “to do list.”

However, not every day is a good day. Sometimes I am in an irrecoverable funk and I just don’t know what to do. When things go wrong like this, it’s easy to fall into a state of frustration and succumb to “analysis paralysis.” Now that your entire schedule is thrown into flux, you can work on any project! What should you do?! Sometimes the best thing to do is to just do something. I don’t spend the rest of the workday trying to come up with a new plan. I’m already in a bad mood, so I probably won’t be able to do my best work anyway. I will often work on one of the less urgent, easier, or more fun tasks, and try again for a better day tommorrow. It’s better than doing nothing.

Work Overtime
I’ve saved the best for last! This is the Mother of all Productivity “Hacks!” And I know some people don’t want to hear this, but people who work longer, produce more. It doesn’t matter how often you meditate or how many kale smoothies you drink. If you work 9 to 5, you will be less productive than someone who is in the shop from 6am to 10pm. If you are new to the idea of working for yourself, you may not yet know that working overtime is a necessity.

When people ask about what I do for a living, and I tell them, I sometimes get a response like, “Oh, It must be nice…”, like I somehow inherited my self-employment, rather than took it on voluntarily. These people probably imagine that I get to take long walks in the morning and that I meet up with my friends for brunch in the afternoon. Ahh, the luxuries of self-employment! I can work whenever I want!

The reality is that if you need to work 16 hours and sleep for 8, and there’s 24 hours in a day… well you do the math.

If it sounds like I’m complaining, I assure you that I’m not. I love to work. I love what I do, but I also simply love working hard and getting things done. And there is an important distinction there. Of course, it is important to love what you do, but running a business involves so much more than the part of the business that involves the art or craft of what you do. There are a lot of not-so-fun things. But if you love what you do and you love to work, then you can enjoy yourself when you’re working in any capacity within the business, whether it’s building guitars, teaching, writing blogs, editing youtube videos, answering emails, marketing, or filing your taxes.

Maybe some day I’ll get to regularly take those morning walks and go out to brunch on a Tuesday, but right now I don’t even desire that kind of life. I’m having too much fun doing what I love to do: Building guitars, teaching, and working hard every day. And the acceptance of that kind of work ethic is the ultimate best practice for productivity.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 2691
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: Shopbot, CAMaster

Re: Best Practices for Productivity as an Independent Crafts

Postby highpockets » Fri Apr 07, 2017 10:37 pm

Randall,

Thanks for sharing, a great read. I resemble a lot of the bad traits he talks about :D :D :D :D :D
John
Maker of Chips
User avatar
highpockets
Vectric Wizard
 
Posts: 1281
Joined: Tue Jan 06, 2015 4:04 pm
Model of CNC Machine: PDJ Pilot Pro

Re: Best Practices for Productivity as an Independent Crafts

Postby scottp55 » Sat Apr 08, 2017 1:52 am

Excellent read Randall, But I'm like John and have a lot of the Bad habits(like checking forums while waiting for my caffeine IV starts taking effect:)
Like you, I make most of my mistakes at the end of long days, when "I only have one more toolpath to cut" :)

I take a page from the author(Hemingway?), who, to paraphrase, said "I stop working on a piece when I'm tired, BUT know EXACTLY what the next paragraph will be....That way I start the day knowing exactly where to start."

I find that "Last Toolpath to do" when tired, usually causes More work, as I'll look at the cut and mean to nudge Z .005" and enter .05"instead,or I'll forget to vac a cutout to make sure it's all the way through, or splinter an edge cutting tabs, or go to sand tabs on oscillating belt and forget the last grit I used was 80G, NOT the 220G I wanted.

I LIKE that Pomodoro thing....gradually have gotten into a habit like that anyways, but didn't realize there was a name for it, and that "sets" existed. After 30 minutes my back will start to kink, and if I try to keep working while distracted, I generally muck something up and spend way more than a 5 minute break either cussing or trying to "rescue"it.

When I ran my bike shop, the first thing I told new employees was something I heard long ago"The customer doesn't always remember the repair was a day late, or $10 over estimate, but he ALWAYS remembers how good a job you did!" Kinda like the saying "How come there's never time enough to do a job right the first time, but ALWAYS time enough to do it right the second time?"

Still remember telling my carpenter crew when they were still in interior final framing stage and wasn't quite right(1/4" off) and I went out of the room after saying "Well if that is the best you can do...we'll just have to leave it.....", came back 2 hours later and it had been entire ripped down/9" nails sawzalled flush/and straight and true chalklines had been snapped:) Later, one of that same crew was doing mortise and tenon closet shelves, and Dougie was cussing that the wall was an 1/4" off plumb in 8' , and his shelf idea demanded better tolerances....I just said "Doug....who built the wall" and he got awful quiet :)
Rambling:)
I should have stopped when I meant to say
Excellent read Randall. :)
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 2077
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: Shopbot Desktop 5.5"Z/spindle/VCP9

Re: Best Practices for Productivity as an Independent Crafts

Postby Adrian » Sat Apr 08, 2017 9:59 am

I don't agree with the communication side of it. It is market dependent to a large extent and how much competition there is but most people who contact someone via social media these days are not expecting to wait more than a few minutes for a reply. Certainly someone who sends a message or an email the evening before is expecting it to be answered the following morning at the very latest. I employ someone to look after the messages in the evenings and if I'm away from the workshop during the day. Social media messaging is the face of a lot of small businesses these days but it's so often treated as an annoyance and something to put off at all costs by the owners.
User avatar
Adrian
Vectric Archimage
 
Posts: 7420
Joined: Thu Nov 23, 2006 2:19 pm
Location: Surrey, UK
Model of CNC Machine: ShopBot PRS Alpha 96x48

Re: Best Practices for Productivity as an Independent Crafts

Postby Leo » Sat Apr 08, 2017 12:42 pm

I have not read it.

I did save it so I could read it later, even if the thread disappears.

I am sure there will be something to learn from the article.

For now, my coffee is finished and I need to get to work.
Imagine the Possibilities of a Creative mind

www.leosworkshop.com
User avatar
Leo
Vectric Wizard
 
Posts: 2418
Joined: Sat Jul 14, 2007 3:02 am
Location: East Freetown, Ma.
Model of CNC Machine: 1300 x 1300 x 254

Re: Best Practices for Productivity as an Independent Crafts

Postby Mark's Wood Chips » Sat Apr 08, 2017 1:39 pm

I can relate to the "putting tools away" section. Something I always do at the end of the job. But then, just as the article mentioned, I keep going with the shop vac until every last molecule of dust is in the bag. I didn't realize that this was a character defect :oops: Scott alluded to stopping when things go amuck. This is something I have learned the hard way - many times. It's painfully difficult to shelve a project until the next day because I want to get it done NOW. Fact is, it's easier to recover from a small mistake than starting over after royally screwing things up.

Mark
User avatar
Mark's Wood Chips
Vectric Craftsman
 
Posts: 113
Joined: Thu Mar 19, 2015 12:36 pm
Location: Hubertus, WI 53033
Model of CNC Machine: PDJ Pilot Pro

Re: Best Practices for Productivity as an Independent Crafts

Postby Ollywood » Thu Apr 13, 2017 2:50 am

Awesome advice - wish I could do all of those.

My advice - stay away from 3D if you can. Bidding takes so long not to get the job!
Ollywood
 
Posts: 40
Joined: Thu Mar 05, 2015 3:31 am
Location: Los Angeles, CA
Model of CNC Machine: FMT Patriot 5 x 10 Plus w/atc

Re: Best Practices for Productivity as an Independent Crafts

Postby scottp55 » Thu Apr 13, 2017 3:10 am

Hint,
To decrease productivity...drop a bottle of CA...run over it with your wheelchair tire...and then put your hand on that exact spot and press down :)
Luckily shelf that CA was on, is directly above my solvent cans:)
Opening Acetone can with only on hand was a challenge:)
Slows productivity WAY down!! :D
User avatar
scottp55
Vectric Wizard
 
Posts: 2077
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: Shopbot Desktop 5.5"Z/spindle/VCP9

Re: Best Practices for Productivity as an Independent Crafts

Postby highpockets » Thu Apr 13, 2017 3:29 am

:D :D :D :D
John
Maker of Chips
User avatar
highpockets
Vectric Wizard
 
Posts: 1281
Joined: Tue Jan 06, 2015 4:04 pm
Model of CNC Machine: PDJ Pilot Pro


Return to Hardware related questions

Who is online

Users browsing this forum: No registered users and 5 guests