Dust collector separator

Dust collector separator

Postby woody53 » Sun Jul 05, 2015 9:28 pm

20150705_141540.jpg
The attachment 20150705_141909.jpg is no longer available
I have a cheaper Harbor Freight dust collector. It is pretty new, and works great. I ran a pine table top for a beer sign, and had to pause everything to get bigger chunks out of the inlet screen. Other than that works good, but that was a real nuisance stopping . I was doing a roughing 3D with 1/2 inch end mill , 1/4 deep @ 130 IMP. Today made a separator barrel, for $ 65 . Doesnt look very good but ran the same toolpath on the same wood, not a piece of wood on the inlet screen afterwards. Still pics up 99% of dust .
Was worth the morning to make.
woody53
Vectric Wizard
 
Posts: 303
Joined: Sat Jun 11, 2011 3:27 pm
Location: Jefferson City, Mo.
Model of CNC Machine: Probotix Meteor 25 x 50

Re: Dust collector separator

Postby ger21 » Sun Jul 05, 2015 11:35 pm

The first thing that most people do is remove the screen. :)
Gerry - http://www.thecncwoodworker.com
ger21
Vectric Wizard
 
Posts: 1478
Joined: Sun Sep 16, 2007 2:59 pm
Location: Shelby Township, MI, USA
Model of CNC Machine: Custom DIY

Re: Dust collector separator

Postby scottp55 » Mon Jul 06, 2015 12:57 am

If you rough against the grain, it pretty much eliminates the big chunks/splinters I've found.
Only 2.5" inlet on my dustfoot, so it used to be Very annoying, and easily clogged until someone tipped me off.
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 3051
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10

Re: Dust collector separator

Postby Mike-S » Wed Jul 15, 2015 3:39 pm

If you can get another lid, I'd suggest repositioning the holes. The one from the CNC should be on the edge (I'm assuming you have a 90 deg elbow inside the can and a baffle.) The output to the vac should be in the center of the lid (center of vortex) so you only suck up fine dust, not chunks. The chunks should be flung to the can's circumference and fall to the bottom.
I have a similar set up and only get a hand-full of dust for each foot of chips in the can.
Attachments
dustcan2.jpg
DC-topHolesPic2.jpg
User avatar
Mike-S
Vectric Wizard
 
Posts: 1092
Joined: Mon Jun 13, 2011 6:45 am
Location: Hayesville, NC
Model of CNC Machine: Joe's Hybrid 4x4 (but 3x3)

Dust collector separator

Postby Bobtail Farm » Sun Jul 19, 2015 7:51 am

Attached is what i built for a similar Harbor Freight dust collector (based on the designs/builds I saw on the internet). I too observe only a small amount of dust in the bag for a lot of waste in the can. My "inlet" is into the side of the can and located between the top of the can and the thein baffle (the plywood I've attached to the top using threaded rod).

Hope the photos help you.
Attachments
IMG_3523 dust separator in place.jpg
IMG_5287 thien baffle and separator lid.jpg
Bobtail Farm
Vectric Craftsman
 
Posts: 132
Joined: Mon Dec 01, 2014 3:53 pm
Model of CNC Machine: Homemade


Return to Hardware related questions

Who is online

Users browsing this forum: No registered users and 3 guests