Words into letters
-
- Posts: 3
- Joined: Wed May 28, 2014 9:41 am
- Model of CNC Machine: Marchant Dice
Words into letters
I don't know if this has been posted before but I'm having trouble separating my words into individual letters. There must be an easy way but I can't seem to figure it out. I can only think of entering them one by one and that can't be right! I'm using VCarve.
Thanks in advance.
Thanks in advance.
- Alan Male
- Vectric Craftsman
- Posts: 173
- Joined: Sat Feb 23, 2013 11:31 pm
- Model of CNC Machine: heiz 400T
- Location: Stevenage - UK
Re: Words into letters
It really depends on what you intend to do with the result.
However, one way is to use the option (Convert object to curves) in the Create Vectors menu.
Cheers,
Alan
However, one way is to use the option (Convert object to curves) in the Create Vectors menu.
Cheers,
Alan
CNC m/c - Heiz 400T
Software - Aspire, VCarve Pro, Photo VCarve, WinPC-NC
CAD - Catia V5
Software - Aspire, VCarve Pro, Photo VCarve, WinPC-NC
CAD - Catia V5
- Mark
- Vectric Staff
- Posts: 1058
- Joined: Sat Aug 18, 2007 2:55 pm
- Model of CNC Machine: CNC Shark, ShopBot, Roland PNC3000
- Location: Alcester U.K.
- Contact:
Re: Words into letters
Hello 12a designs,
You can right hand click on the text and select the option to "Convert to Curves" option to split the text into individual vectors.
If you would like to alter the spacing of the letters within the text, you can use the "Edit text Spacing and Curve" tool.
http://support.vectric.com/aspire-quest ... xt-spacing
http://www.vectric.org/video/aspire4-vc ... /G01-w.mp4
I hope that this helps.
You can right hand click on the text and select the option to "Convert to Curves" option to split the text into individual vectors.
If you would like to alter the spacing of the letters within the text, you can use the "Edit text Spacing and Curve" tool.
http://support.vectric.com/aspire-quest ... xt-spacing
http://www.vectric.org/video/aspire4-vc ... /G01-w.mp4
I hope that this helps.
-
- Posts: 3
- Joined: Wed May 28, 2014 9:41 am
- Model of CNC Machine: Marchant Dice
Re: Words into letters
Thanks both - I was wary of doing this as I thought I would end up with curved, rather than straight, letters. I'll give it a go.
Thanks again
Thanks again
-
- Vectric Wizard
- Posts: 414
- Joined: Wed Apr 01, 2009 12:15 am
- Location: Dunnellon, Florida
Re: Words into letters
Hi: Also, if you select node editing and click on the word, you'll get a note asking effectively to make each letter an individual entity. Select ok and each letter can be played with at will.
-
- Posts: 3
- Joined: Wed May 28, 2014 9:41 am
- Model of CNC Machine: Marchant Dice
Re: Words into letters
Hi Norman, only just seen this reply - thanks. I'll give this a go as the curve one is fine but I like to have options
Was wondering though, once I've split my words into letters how do I tell what font it was? Is it just as simple as either incorporating the font into the file name, or leaving a comment in the toolpath?
Thanks
Jaine
Was wondering though, once I've split my words into letters how do I tell what font it was? Is it just as simple as either incorporating the font into the file name, or leaving a comment in the toolpath?
Thanks
Jaine
-
- Vectric Craftsman
- Posts: 288
- Joined: Fri Jul 26, 2013 8:01 pm
- Model of CNC Machine: PAE 110SD Series/Mach3 Software
Re: Words into letters
Haven't done text in awhile but I believe if you highlight a piece of text then hit the text tool (will reopen it and allow for editing) it should tell you what font it is.12a designs wrote:Hi Norman, only just seen this reply - thanks. I'll give this a go as the curve one is fine but I like to have options
Was wondering though, once I've split my words into letters how do I tell what font it was? Is it just as simple as either incorporating the font into the file name, or leaving a comment in the toolpath?
Thanks
Jaine
-
- Vectric Craftsman
- Posts: 288
- Joined: Fri Jul 26, 2013 8:01 pm
- Model of CNC Machine: PAE 110SD Series/Mach3 Software
Re: Words into letters
Just tried what I mentioned before, did not want to leave misinformation out there. That method will work if you have not converted the text to curves.
- Ms Wolffie
- Vectric Wizard
- Posts: 2695
- Joined: Sat Mar 31, 2012 10:41 pm
- Model of CNC Machine: Blue Elephant 1325, Shark HD Pro
- Location: Tully Heads, Wet Tropics, Queensland, Australia
Re: Words into letters
Haven't done lettering in a while but AFSIK you just ungroup the letters.
Cheers
Wolffie
Whatshammacallit
Cut3D, VCarvePro 6.5, Aspire4, PhotoVCarve, Corel Graphics Suite X6
Wolffie
Whatshammacallit
Cut3D, VCarvePro 6.5, Aspire4, PhotoVCarve, Corel Graphics Suite X6
-
- Vectric Wizard
- Posts: 586
- Joined: Sat Jan 08, 2011 12:29 pm
- Model of CNC Machine: Professional done home built.
- Location: SW Michigan
Re: Words into letters
You can make notes within your project.how do I tell what font it was? I
In the Tool path Control there is a box labeled Notes. There you can store info about the job such as font etc. Far Right very bottom button.