Hall of Lines

This is the place to post images of work produced using Aspire

Hall of Lines

Postby nicksilva » Wed Sep 11, 2019 11:56 pm

IMG_2436 (1).jpg
Broke in my 10.0 with this 3D illusion piece. 4.5” in Mesquite.
It's just a simple VCarving and would work in either Aspire or VC.
Create everyday.
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 257
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: Hall of Lines

Postby scottp55 » Thu Sep 12, 2019 12:05 am

Nice piece Nick!
Though my first thought was "That would be a tough path with a wheelchair to change your mind on" :)
Thanks!
scott
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 3056
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10

Re: Hall of Lines

Postby nicksilva » Thu Sep 12, 2019 3:24 am

thank you. yeah, it should probably be River of lines, 'cause if you're caught up in the current - well you know/
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 257
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: Hall of Lines

Postby Leo » Thu Sep 12, 2019 12:53 pm

scottp55 wrote:Nice piece Nick!
Though my first thought was "That would be a tough path with a wheelchair to change your mind on" :)
Thanks!
scott


Knowing you -- I think you would get in the groove and just GO.

I don't think there is much holding you back.
Imagine the Possibilities of a Creative mind

www.leosworkshop.com
User avatar
Leo
Vectric Wizard
 
Posts: 2950
Joined: Sat Jul 14, 2007 3:02 am
Location: East Freetown, Ma.
Model of CNC Machine: 1300 x 1300 x 254

Re: Hall of Lines

Postby scottp55 » Thu Sep 12, 2019 1:28 pm

Thanks Leo, but on this one I'd just have pick a groove and trust Nick not to take me to a waterfall or a Rabbit Hole :)
Nice 3D Delusion Nick:)
scott
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 3056
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10

Re: Hall of Lines

Postby nicksilva » Thu Sep 12, 2019 1:32 pm

scottp55 wrote:....I'd just have pick a groove and trust Nick not to take me to a waterfall or a Rabbit Hole......
scott


what do you think is around the corner? :D
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 257
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: Hall of Lines

Postby scottp55 » Thu Sep 12, 2019 1:59 pm

Reminded me of a wildwater race in Massachusetts Nick:)
Scoped out the river the day before, and picked out our lines.....THEN the day of the race they opened 3 more sluices on the dam above :shock:
Another 4 feet of water, and wasn't a problem for most of the wildwater, BUT there was a GORGE with what WAS a 5 foot drop and only one real way to go over, that lead you directly to the only path through the Class4 "Rock Garden" below.
NOW it was 8-10 foot drop with a WHIRLPOOL in the center, and 60 foot wide selection of ledge choices, and "Rock Garden" now had 10 ways in, BUT only ONE led you to the main river stream :D

Three wetsuited dive teams at the drop that were kept busy, and paddlers from cross country were madly scrambling and carrying their boats over the Garden when the paths they were washed into petered out to boulders :D :D

Probably a 100 foot waterfall Nick!!!! :) :)
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 3056
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10

Re: Hall of Lines

Postby nicksilva » Thu Sep 12, 2019 2:08 pm

scottp55 wrote:Reminded me of a wildwater race in Massachusetts Nick:)
Probably a 100 foot waterfall Nick!!!! :) :)


DANG! And I have trouble jumping into the deep end of the pool.
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 257
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: Hall of Lines

Postby scottp55 » Thu Sep 12, 2019 2:16 pm

:)
scott
User avatar
scottp55
Vectric Wizard
 
Posts: 3056
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP10

Re: Hall of Lines

Postby Creation in Wood » Tue Sep 24, 2019 3:51 pm

Thank you
Thank You
Doug
User avatar
Creation in Wood
Vectric Wizard
 
Posts: 448
Joined: Thu May 28, 2015 8:58 pm
Location: Monument, Colorado USA
Model of CNC Machine: Legacy Maverick CNC 4x8


Return to Aspire - Gallery

Who is online

Users browsing this forum: No registered users and 16 guests