Gryphon in Poplar
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Gryphon in Poplar
Gryphon in Home Depot Poplar. Machine time: 110 minutes with a 1/8" ballnose @9% stepover
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Craftsman
- Posts: 216
- Joined: Sat Feb 03, 2018 2:03 am
- Model of CNC Machine: diy 4 X 4 CNC Router
- Location: So. Cal.
Re: Gryphon in Poplar
Very Nice, Like it alot.
mark-s
mark-s
-
- Vectric Wizard
- Posts: 1012
- Joined: Fri May 15, 2015 1:10 pm
- Model of CNC Machine: 3 axis small size machine
- Location: France
Re: Gryphon in Poplar
Very clean cut, especially in a soft wood.
Is it out of the machine or did you sand it?
Is it out of the machine or did you sand it?
Best regards
Didier
W7 - Aspire 8.517
Didier
W7 - Aspire 8.517
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Gryphon in Poplar
I did about 2 minutes of sanding to knock the fuzzies off. Wish I could remember where I bought the 1/8" ball nose bit. It might be a Hertel.Is it out of the machine or did you sand it?
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
-
- Vectric Craftsman
- Posts: 193
- Joined: Sun Nov 04, 2012 4:27 pm
- Model of CNC Machine: PRS Buddy48alpha ,4x6' 130w laser, Wazer
Re: Gryphon in Poplar
Very nice Randall- I did the same gryphon in Corian this weekend- my first carve with my new [to me] BT48 alpha.
-
- Vectric Craftsman
- Posts: 216
- Joined: Sat Feb 03, 2018 2:03 am
- Model of CNC Machine: diy 4 X 4 CNC Router
- Location: So. Cal.
Re: Gryphon in Poplar
Rcnewcomb how deep was that cut?
Thanks
mark-s
Thanks
mark-s
- Rcnewcomb
- Vectric Archimage
- Posts: 5887
- Joined: Fri Nov 04, 2005 5:54 am
- Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
- Location: San Jose, California, USA
- Contact:
Re: Gryphon in Poplar
Just under 0.4" so I was able to use a bit with 1/2" cutting length with no roughing pass.Rcnewcomb how deep was that cut?
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop
10 fingers in, 10 fingers out, another good day in the shop
- Makingtoothpicks
- Vectric Wizard
- Posts: 520
- Joined: Tue Jul 23, 2013 8:46 pm
- Model of CNC Machine: Cncrouterparts CPR2448
- Location: Burien, Wa
- Contact:
Re: Gryphon in Poplar
The Gryphon model is that an Aspire model or Design and Make
Don
Don
- highpockets
- Vectric Wizard
- Posts: 3667
- Joined: Tue Jan 06, 2015 4:04 pm
- Model of CNC Machine: PDJ Pilot Pro
- Creation in Wood
- Vectric Wizard
- Posts: 856
- Joined: Thu May 28, 2015 8:58 pm
- Model of CNC Machine: Legacy Maverick ATC 4x8 CNC
- Location: Monument, Colorado USA