Gryphon in Poplar

This is the place to post images of work produced using Aspire

Gryphon in Poplar

Postby Rcnewcomb » Mon Aug 13, 2018 1:56 am

Gryphon in Home Depot Poplar. Machine time: 110 minutes with a 1/8" ballnose @9% stepover
Attachments
SmallGryphon.jpg
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3069
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Gryphon in Poplar

Postby mark-s » Mon Aug 13, 2018 2:12 am

Very Nice, Like it alot.
mark-s
mark-s
Vectric Apprentice
 
Posts: 61
Joined: Sat Feb 03, 2018 2:03 am
Model of CNC Machine: diy cnc router

Re: Gryphon in Poplar

Postby LittleGreyMan » Mon Aug 13, 2018 8:03 am

Very clean cut, especially in a soft wood.

Is it out of the machine or did you sand it?
Best regards

LGM

W7 - Aspire 8.517
LittleGreyMan
Vectric Wizard
 
Posts: 774
Joined: Fri May 15, 2015 1:10 pm
Location: France
Model of CNC Machine: 3 axis small size machine

Re: Gryphon in Poplar

Postby Rcnewcomb » Mon Aug 13, 2018 3:43 pm

Is it out of the machine or did you sand it?

I did about 2 minutes of sanding to knock the fuzzies off. Wish I could remember where I bought the 1/8" ball nose bit. It might be a Hertel.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3069
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Gryphon in Poplar

Postby GeneMpls » Mon Aug 13, 2018 5:30 pm

Very nice Randall- I did the same gryphon in Corian this weekend- my first carve with my new [to me] BT48 alpha.
DSC00963.JPG
GeneMpls
Vectric Craftsman
 
Posts: 128
Joined: Sun Nov 04, 2012 4:27 pm
Model of CNC Machine: 4x4 PRS and 3x4' 130w laser

Re: Gryphon in Poplar

Postby mark-s » Mon Aug 13, 2018 6:59 pm

Rcnewcomb how deep was that cut?
Thanks
mark-s
mark-s
Vectric Apprentice
 
Posts: 61
Joined: Sat Feb 03, 2018 2:03 am
Model of CNC Machine: diy cnc router

Re: Gryphon in Poplar

Postby Rcnewcomb » Mon Aug 13, 2018 7:49 pm

Rcnewcomb how deep was that cut?

Just under 0.4" so I was able to use a bit with 1/2" cutting length with no roughing pass.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
User avatar
Rcnewcomb
Vectric Wizard
 
Posts: 3069
Joined: Fri Nov 04, 2005 5:54 am
Location: San Jose, California, USA
Model of CNC Machine: GCnC/WinCNC

Re: Gryphon in Poplar

Postby Makingtoothpicks » Sat Aug 18, 2018 8:09 pm

The Gryphon model is that an Aspire model or Design and Make

Don
User avatar
Makingtoothpicks
Vectric Wizard
 
Posts: 458
Joined: Tue Jul 23, 2013 8:46 pm
Location: Burien, Wa
Model of CNC Machine: Cncrouterparts CPR2448

Re: Gryphon in Poplar

Postby highpockets » Sat Aug 18, 2018 8:21 pm

Aspire, Gryphon-57616-A.3dClip
John
Maker of Chips
User avatar
highpockets
Vectric Wizard
 
Posts: 1773
Joined: Tue Jan 06, 2015 4:04 pm
Model of CNC Machine: PDJ Pilot Pro

Re: Gryphon in Poplar

Postby Creation in Wood » Sun Aug 19, 2018 10:13 pm

Very nice
Thank You
Doug
User avatar
Creation in Wood
Vectric Wizard
 
Posts: 361
Joined: Thu May 28, 2015 8:58 pm
Location: Monument, Colorado USA
Model of CNC Machine: Legacy Maverick CNC 4x8


Return to Aspire - Gallery

Who is online

Users browsing this forum: No registered users and 20 guests