Gryphon in Poplar

This is the place to post images of work produced using Aspire
Post Reply
User avatar
Rcnewcomb
Vectric Archimage
Posts: 5886
Joined: Fri Nov 04, 2005 5:54 am
Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
Location: San Jose, California, USA
Contact:

Gryphon in Poplar

Post by Rcnewcomb »

Gryphon in Home Depot Poplar. Machine time: 110 minutes with a 1/8" ballnose @9% stepover
Attachments
SmallGryphon.jpg
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop

mark-s
Vectric Craftsman
Posts: 216
Joined: Sat Feb 03, 2018 2:03 am
Model of CNC Machine: diy 4 X 4 CNC Router
Location: So. Cal.

Re: Gryphon in Poplar

Post by mark-s »

Very Nice, Like it alot.
mark-s

LittleGreyMan
Vectric Wizard
Posts: 1012
Joined: Fri May 15, 2015 1:10 pm
Model of CNC Machine: 3 axis small size machine
Location: France

Re: Gryphon in Poplar

Post by LittleGreyMan »

Very clean cut, especially in a soft wood.

Is it out of the machine or did you sand it?
Best regards

Didier

W7 - Aspire 8.517

User avatar
Rcnewcomb
Vectric Archimage
Posts: 5886
Joined: Fri Nov 04, 2005 5:54 am
Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
Location: San Jose, California, USA
Contact:

Re: Gryphon in Poplar

Post by Rcnewcomb »

Is it out of the machine or did you sand it?
I did about 2 minutes of sanding to knock the fuzzies off. Wish I could remember where I bought the 1/8" ball nose bit. It might be a Hertel.
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop

GeneMpls
Vectric Craftsman
Posts: 193
Joined: Sun Nov 04, 2012 4:27 pm
Model of CNC Machine: PRS Buddy48alpha ,4x6' 130w laser, Wazer

Re: Gryphon in Poplar

Post by GeneMpls »

Very nice Randall- I did the same gryphon in Corian this weekend- my first carve with my new [to me] BT48 alpha.
DSC00963.JPG

mark-s
Vectric Craftsman
Posts: 216
Joined: Sat Feb 03, 2018 2:03 am
Model of CNC Machine: diy 4 X 4 CNC Router
Location: So. Cal.

Re: Gryphon in Poplar

Post by mark-s »

Rcnewcomb how deep was that cut?
Thanks
mark-s

User avatar
Rcnewcomb
Vectric Archimage
Posts: 5886
Joined: Fri Nov 04, 2005 5:54 am
Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
Location: San Jose, California, USA
Contact:

Re: Gryphon in Poplar

Post by Rcnewcomb »

Rcnewcomb how deep was that cut?
Just under 0.4" so I was able to use a bit with 1/2" cutting length with no roughing pass.
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop

User avatar
Makingtoothpicks
Vectric Wizard
Posts: 520
Joined: Tue Jul 23, 2013 8:46 pm
Model of CNC Machine: Cncrouterparts CPR2448
Location: Burien, Wa
Contact:

Re: Gryphon in Poplar

Post by Makingtoothpicks »

The Gryphon model is that an Aspire model or Design and Make

Don

User avatar
highpockets
Vectric Wizard
Posts: 3667
Joined: Tue Jan 06, 2015 4:04 pm
Model of CNC Machine: PDJ Pilot Pro

Re: Gryphon in Poplar

Post by highpockets »

Aspire, Gryphon-57616-A.3dClip
John
Maker of Chips

User avatar
Creation in Wood
Vectric Wizard
Posts: 856
Joined: Thu May 28, 2015 8:58 pm
Model of CNC Machine: Legacy Maverick ATC 4x8 CNC
Location: Monument, Colorado USA

Re: Gryphon in Poplar

Post by Creation in Wood »

Very nice
Thank You
Doug

Post Reply