SOA 3d

This is the place to post images of work produced using Aspire

SOA 3d

Postby Xxray » Sun May 10, 2015 4:54 am

Here is a rendering of the sons of anarchy reaper.
Is about 12x10" done out of .75 poplar, took about 4 hours to cut with a 1/32 tapered ball nose. Don't know how well it shows in the pic but many of the smaller areas and along the edges got burnt, this is due to my bit being a little dull, plus I didn't use a roughing pass and it really bit into the wood. Burns don't look bad anyhow, but I really need a new bit. Just used 2 poly clear coats on it.
Am doing another in walnut as I speak, looks flawless so far, I am doing this "standing proud" plus I did use a roughing on this one, so should turn out better, will post when able [shaping up to be a 6 hr cut, I'll be up to 4am waiting on it].
[ps - Don't tell Jax I made this, he'll kick my a$% !]
Attachments
FullSizeRender.jpg
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby krugshouse » Sun May 10, 2015 12:38 pm

Thats beautiful work. I'm a big SAMCRO fan.
Have a safe machining day
User avatar
krugshouse
 
Posts: 44
Joined: Sat Mar 03, 2012 11:37 pm
Location: New Jersey
Model of CNC Machine: Blackfoot v4.2, VCP 8, Mach 3

Re: SOA 3d

Postby nicksilva » Sun May 10, 2015 1:50 pm

very nice! I got the same model. I'm planning to make a leather embossing plate with it.
cheers!
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 217
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: SOA 3d

Postby Xxray » Mon May 11, 2015 3:14 am

Walnut, same size as the poplar. Nearly 6 hours but the "proud" look was worth the extra time, am doing a purple heart as I speak - Note to self: Start 6 hour projects a bit earlier !
Attachments
FullSizeRessnder.jpg
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby MTSO » Mon May 11, 2015 3:24 am

the finished product looks really good, where did you get the model from?.

regards

Brian
MTSO
Vectric Craftsman
 
Posts: 214
Joined: Tue Mar 11, 2014 6:12 pm
Location: Auckland New Zealand
Model of CNC Machine: salecnc XJ1224

Re: SOA 3d

Postby Xxray » Mon May 11, 2015 7:56 am

got this one off ebay
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby COWBOY1296 » Mon May 11, 2015 1:38 pm

I liked the SOA, watched every episode on Netflix. It is easy to identify with the characters. And a lot of those actors in real life support wounded warriors and i have seen pictures of them interacting with marines at Camp Pendleton. But the characters they played were all crooks, even the cops were crooks. But it was a great series, especially since i ride a Harley.
COWBOY1296
Vectric Wizard
 
Posts: 635
Joined: Thu Apr 15, 2010 10:03 pm
Location: SOUTH CENTRAL COLORADO
Model of CNC Machine: SHOPBOT BUDDY PRS 32, 4 FT PWR STICK

Re: SOA 3d

Postby Xxray » Mon May 11, 2015 3:54 pm

Very good show, no doubt. I have some close insight into outlaw clubs, alot of their stuff is spot on, some not even close. Most outlaw guys I know love it, put a little extra aura on them by default.
The crescendo of violence towards the last season was so far over the top that it made me cringe, but that tends to be the way series like this develop, they have to outdo themselves each and every week and end up getting ludicrous. But the majority of the series was a good watch, I heard they might be doing a prequel series, going back to the roots of the club.
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby Xxray » Tue May 12, 2015 3:40 am

On a roll, purple heart ,, Started this one much earlier !
Might do a wenge and that'll be about it
Attachments
FullSizxxeRender.jpg
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby Xxray » Wed May 13, 2015 6:36 am

Wenge, fresh off the table, should look stellar once its cleaned up and clear coat applied.

Luck of the draw on the rifle, is one of the highest points and it picked up some striking grain patterns that faded out deeper down, almost as if by design.
Walnut already sold so I'll be making another one of those.
Attachments
IMG_061aa1.JPG
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby scottp55 » Wed May 13, 2015 1:05 pm

Make sure to show a pic of Wenge when Finished :)
Should be Striking!
User avatar
scottp55
Vectric Wizard
 
Posts: 2077
Joined: Thu May 09, 2013 11:30 am
Location: Kennebunkport, Maine, US
Model of CNC Machine: Shopbot Desktop 5.5"Z/spindle/VCP9

Re: SOA 3d

Postby Xxray » Thu May 14, 2015 3:41 am

Here she is
Attachments
FaaullSizeRender.jpg
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby tonydude » Thu May 14, 2015 4:02 am

Like that finish, really came out nice.

Tony
tonydude
Vectric Apprentice
 
Posts: 76
Joined: Fri Apr 10, 2009 2:28 am

Re: SOA 3d

Postby Xxray » Thu May 14, 2015 5:20 am

Thanks, I usually use flat but this is a semi gloss, highlights the details well without the over the top glare of gloss.

For holding detail, nothing beats wenge, very hard and dense wood. Downsides are the graining can be a grab bag, with some slabs jaw dropping and other areas in the same slab mediocre ,,, And very expensive and pretty hard to come by.
Doug
User avatar
Xxray
Vectric Wizard
 
Posts: 1663
Joined: Thu Feb 17, 2011 8:47 am
Location: MI USA
Model of CNC Machine: CAMaster Stinger 1

Re: SOA 3d

Postby phill05 » Thu May 14, 2015 12:30 pm

Lovely work I think the Wenge looks more in tune to the subject.
phill05
Vectric Apprentice
 
Posts: 75
Joined: Thu Oct 14, 2010 2:40 pm
Location: Derbyshire UK
Model of CNC Machine: Hybrid re-build

Next

Return to Aspire - Gallery

Who is online

Users browsing this forum: RickCNC and 9 guests