Purple Heart Wood - Questions for Carving

This section is for useful tips and tricks for Aspire
Post Reply
xoneeleven
Vectric Apprentice
Posts: 51
Joined: Thu May 19, 2016 10:59 pm
Model of CNC Machine: Camaster Stinger III - 2.25 hp spindle
Location: North Idaho

Purple Heart Wood - Questions for Carving

Post by xoneeleven »

Has anyone had good results carving on Purple Heart wood?

We tried carving a model we acquired from Design and Make, with terrible results.

The grain on the purple heart was long, and very stiff. The stiffness caused the grain to break off in long, skinny pieces.
The cutting direction was "with" the grain.

Has anyone here tried carving on Purple Heart wood? If so, what results did you have, and do you have any tips for carving it?

Thanks...

Mark

Mobius
Vectric Wizard
Posts: 413
Joined: Wed Jul 09, 2014 1:19 am
Model of CNC Machine: CRP Pro 4848 Custom Build
Location: Drumheller, Alberta, Canada
Contact:

Re: Purple Heart Wood - Questions for Carving

Post by Mobius »

I can't say I've every had a problem. I love using purple heart for V-inlays as it is so dense and holds detail nicely.

The obvious answer here is to not cut with the grain. Try running the job at a shallow angle across the grain, say 10º. Haven't tried it myself but you may get both benefits of cutting with the grain, but enough lateral movement to prevent tearing.
Connor Bredin
Distinctive Dimensional Concepts Ltd.
www.distinctive-concepts.ca

User avatar
mtylerfl
Vectric Archimage
Posts: 5865
Joined: Thu Jan 29, 2009 3:54 am
Model of CNC Machine: -CarveWright CNC -ShopBot Buddy PRSAlpha
Location: Brunswick, GA

Re: Purple Heart Wood - Questions for Carving

Post by mtylerfl »

xoneeleven wrote:...

The grain on the purple heart was long, and very stiff. The stiffness caused the grain to break off in long, skinny pieces.
The cutting direction was "with" the grain...
Could be a number of factors. Depth per pass set too deep, and/or stepover set too wide would be among the first things to consider. I prefer cutting (3D carving) with the grain and have never had a problem.
Michael Tyler

facebook.com/carvebuddy

-CarveWright CNC
-ShopBot Buddy PRSAlpha CNC

xoneeleven
Vectric Apprentice
Posts: 51
Joined: Thu May 19, 2016 10:59 pm
Model of CNC Machine: Camaster Stinger III - 2.25 hp spindle
Location: North Idaho

Re: Purple Heart Wood - Questions for Carving

Post by xoneeleven »

Mobius wrote:I can't say I've every had a problem. I love using purple heart for V-inlays as it is so dense and holds detail nicely.

The obvious answer here is to not cut with the grain. Try running the job at a shallow angle across the grain, say 10º. Haven't tried it myself but you may get both benefits of cutting with the grain, but enough lateral movement to prevent tearing.

We will try cutting against the grain, next. Hopefully the results will be better.

We are using good quality bits, and using a CNC Calc for feeds and speeds.

Thanks for the tip

xoneeleven
Vectric Apprentice
Posts: 51
Joined: Thu May 19, 2016 10:59 pm
Model of CNC Machine: Camaster Stinger III - 2.25 hp spindle
Location: North Idaho

Re: Purple Heart Wood - Questions for Carving

Post by xoneeleven »

mtylerfl wrote:
xoneeleven wrote:...

The grain on the purple heart was long, and very stiff. The stiffness caused the grain to break off in long, skinny pieces.
The cutting direction was "with" the grain...
Could be a number of factors. Depth per pass set too deep, and/or stepover set too wide would be among the first things to consider. I prefer cutting (3D carving) with the grain and have never had a problem.
Hello Mike,
I am pretty sure we have dialed in the correct depth and stepover.

One thing we did notice, is the bit got very hot during the finish cut (the bit is an Amana 46282, 5.4 deg tapered ball nose).
Perhaps the bit life ended while cutting this piece. We have replaced this bit with a fresh one and will cut against the grain on the next run.

Mark

User avatar
scottp55
Vectric Wizard
Posts: 4713
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
Location: Kennebunkport, Maine, US

Re: Purple Heart Wood - Questions for Carving

Post by scottp55 »

Mark,
You may still want to post a screenshot of the feeds/speeds you're using(the edit box in the actual toolpath).
Calculators don't always give the best info for your machine/bit/and material.
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.

xoneeleven
Vectric Apprentice
Posts: 51
Joined: Thu May 19, 2016 10:59 pm
Model of CNC Machine: Camaster Stinger III - 2.25 hp spindle
Location: North Idaho

Re: Purple Heart Wood - Questions for Carving

Post by xoneeleven »

scottp55 wrote:Mark,
You may still want to post a screenshot of the feeds/speeds you're using(the edit box in the actual toolpath).
Calculators don't always give the best info for your machine/bit/and material.
scott
Here are the feed/speed details
Screenshot
Screenshot

User avatar
Rcnewcomb
Vectric Archimage
Posts: 5886
Joined: Fri Nov 04, 2005 5:54 am
Model of CNC Machine: 24x36 GCnC/WinCNC with ATC
Location: San Jose, California, USA
Contact:

Re: Purple Heart Wood - Questions for Carving

Post by Rcnewcomb »

I'd use a 10% stepover and increase the plunge rate to match the feed rate.
- Randall Newcomb
10 fingers in, 10 fingers out, another good day in the shop

xoneeleven
Vectric Apprentice
Posts: 51
Joined: Thu May 19, 2016 10:59 pm
Model of CNC Machine: Camaster Stinger III - 2.25 hp spindle
Location: North Idaho

Re: Purple Heart Wood - Questions for Carving

Post by xoneeleven »

Rcnewcomb wrote:I'd use a 10% stepover and increase the plunge rate to match the feed rate.
Thanks

We will make the adjustments and check the results.

Mark

User avatar
dhellew2
Vectric Wizard
Posts: 1322
Joined: Thu May 22, 2008 10:14 pm
Model of CNC Machine: Legacy Artisan 72 and AVID CNC Rotary
Location: Royal City Washington

Re: Purple Heart Wood - Questions for Carving

Post by dhellew2 »

Other possible considerations:
Use a spiral bit, better yet use a 3-flute spiral bit
Check out www.cuttingtoolsource.com

I typically use an 8% stepover but then again I mostly use very small bits.. ie 1mm
If the bit is getting too hot there are 3 basic reasons:
1. feed rate
2. rpm
3. dull bit

Good luck,
Dale
You will get old if you live long enough!
Young = time, no money
Old = money, no time
Dale

User avatar
scottp55
Vectric Wizard
Posts: 4713
Joined: Thu May 09, 2013 11:30 am
Model of CNC Machine: ShopbotDesktop 5.5"Z/spindle/VCP11.5
Location: Kennebunkport, Maine, US

Re: Purple Heart Wood - Questions for Carving

Post by scottp55 »

Yep, Randall got it:)
The plunge feed was slowing EVERYTHING down, which resulted in the excess heating of the bit.
Should be better now.
scott
I've learned my lesson well. You can't please everyone,so you have to please yourself
R.N.

User avatar
Xxray
Vectric Wizard
Posts: 2300
Joined: Thu Feb 17, 2011 8:47 am
Model of CNC Machine: CAMaster Stinger 1
Location: MI USA

Re: Purple Heart Wood - Questions for Carving

Post by Xxray »

I have made dozens of 3d models with PH and never had a problem, has always been one of my favorite woods to work with. Usually comes off the table so nice it barely needs any sanding.
Doug

Post Reply