Plate holder

Post by **Makingtoothpicks** » Thu Dec 21, 2017 12:19 am

Does anyone have a simple design for a plate holder. I need to make one
to hold a small sign about 11 x 11.

Thank you
Don

Post by **Buc** » Thu Dec 21, 2017 1:34 am

Don,
try this nice design http://forum.vectric.com/viewtopic.php? ... and#p66486

Buc

Post by **Makingtoothpicks** » Thu Dec 21, 2017 2:31 am

I like that one will give it a try. Should work
Thank You Buc

Don

Post by **highpockets** » Thu Dec 21, 2017 3:22 am

I like Buc's plate holder.

Here's another one that I created for the Tree of Life project.
http://forum.vectric.com/search.php?key ... ee+of+life

Post by **Buc** » Thu Dec 21, 2017 5:24 am

Don't thank me, thank 'Turtle 49,'
Buc

Post by **jerry carney** » Thu Dec 21, 2017 3:56 pm

I made the same holder as High Pockets, and I make up 5 or 6 just to have available when needed.

Post by **Makingtoothpicks** » Thu Dec 21, 2017 6:34 pm

Thank you Highpockets that is the one I was looking for. Now I have 2

Don

Post by **signcut329** » Sat Dec 23, 2017 9:29 pm

Here is a very simple holder that can be resized to hold just about anything.

P.S. I copy and paste, then stack 1/4 inch MDF to make several at one time. Regular water based stain works well on MDF also.

Post by **signcut329** » Sat Dec 23, 2017 9:39 pm

Here is another version of the simple plate/plaque/picture frame holder. this one has legs that will hold it higher for round objects like plates.

Post by **Makingtoothpicks** » Sun Dec 24, 2017 7:48 pm

Thank you for all the designs. I cannot open the 2 crv3d as they are Aspire only.
I did open them in the trial version but cannot copy the vectors into VC9.

Thank You
Don

Post by **signcut329** » Sun Dec 24, 2017 9:43 pm

Added the file as a .crv see if this works. If not will send in .dxf format.

Merry Christmas to ALL!

Post by **martin54** » Sun Dec 24, 2017 11:04 pm

signcut329 wrote:Added the file as a .crv see if this works. If not will send in .dxf format.

Merry Christmas to ALL!

If it is just vectors then it will save & open OK as a .crv file as long as you are using the correct version of the software

Post by **signcut329** » Sun Dec 24, 2017 11:35 pm

Here is the other one in crv format.

Post by **Makingtoothpicks** » Mon Dec 25, 2017 8:48 am

Thank you for the CRV version.

Merry Christmas to all and a Happy New Year

Don

Post by **sharkcutup** » Mon Dec 25, 2017 4:41 pm

For those of us who have not upgraded to V-Carve version 9.0 I have taken the liberty of re-drawing the 4.5 in stand in V-Carve version 8.5

Enjoy!

Merry Christmas Everyone!!! Have a GREAT HOLIDAY!!!

4.5 in stand_8.5.crv: (24 KiB) Downloaded 144 times

Sharkcutup

Vectric Customer

Plate holder

Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder

Re: Plate holder