space shuttle

The Gallery is for posting photographs and images of work machined using Cut2D

space shuttle

Postby cdrd03 » Wed Oct 15, 2014 7:09 pm

I have had Cut2d for some time and due to my machine being a table top I was limited to small projects (small signs and puzzles). I recently finished a larger machine and have been having fun learning its limitations (as well as mine). Well my daughter is a band director here in Indiana. She asked me to make her an 8 foot space shuttle. The limitation that I was given was that it had to be sturdy because it was going to be pulled across the football field during their performance, but it also had to be as light as possible. The other limitation given was that it had to be able to be taken apart and put into a trailer with the other props, instruments, and uniforms that have to be transported between competitions.

The center and nose have a mdf skeleton and is wrapped in felt and fiberglass. The tail section is laminated foam board with 2 half inch rods through its center. These rods slide into 2 receivers in the center skeleton section. The wings are 3 1 inch laminated foam boards with a 3/8 plywood backer. This is mounted to 1/4 plate mounted between the mdf sections in the skeleton. I should have used smaller plate, but 1/4 is what I had on hand.

Overall it was a fun and challenging project. I had to teach myself how to fiberglass, which will come in handy which another project that I have planned for the spring. My daughter and the kids were really excited when they received the shuttle. They did the final detail painting on it and I have not received photos of it yet.

Chuck
Attachments
Center Section 1.png
Skeleton.png
Wing Mounting Plates.png
One of these Plates are between each section and there
are 4 hole drilled (2 for each wing) and tapped for a
3/8s bolt.
Pre Forming.png
Dry fit before shaping the wings
1st layer Fiberglass.png
This is where I really started learning what not to do with fiberglass.
Then I had to remind myself that if you cant see it from 50 yards away
it should be ok.
Complete on cart 1.png
The finished product before the kids put there stamp on it
cdrd03
 
Posts: 22
Joined: Wed May 09, 2012 4:39 am
Model of CNC Machine: DIY Wooden Router

Re: space shuttle

Postby pops1964 » Wed Oct 15, 2014 9:34 pm

Very cool.
POPS1964
SHOPBOT Buddy BT-32
pops1964
Vectric Wizard
 
Posts: 322
Joined: Sun Jun 22, 2014 11:09 pm
Location: Michigan USA
Model of CNC Machine: shopbot buddy bt 32

Re: space shuttle

Postby cnc4me » Wed Oct 15, 2014 10:32 pm

Nicely done !
cnc4me
Vectric Apprentice
 
Posts: 62
Joined: Wed Dec 29, 2010 8:03 pm
Location: Sylvania, Ohio, USA
Model of CNC Machine: XYZ Gantry, PMDX motion, Mach3

Re: space shuttle

Postby nicksilva » Thu Oct 16, 2014 1:54 pm

Houston, we have awsome!
"Out of my mind. Back in 5 Minutes."
nicksilva
Vectric Craftsman
 
Posts: 217
Joined: Thu Aug 21, 2014 8:13 pm
Location: Dallas, TX USA
Model of CNC Machine: ULS M300, Rockler 60th Ann. Shark

Re: space shuttle

Postby bogusz87 » Sun Feb 22, 2015 8:06 pm

great work!
website:
www.portretywdrewnie.pl
User avatar
bogusz87
 
Posts: 11
Joined: Wed Jun 05, 2013 6:18 pm
Location: Poznań
Model of CNC Machine: INFOTEC


Return to Cut2D - Gallery

Who is online

Users browsing this forum: No registered users and 3 guests