Crazy Rabbit...
Crazy Rabbit...
Hello there...
here is a little funny - Crazy Bunny
Thanks a lot on dasch, with your ( and a another decent chap ) tips/tut´s i build this 3D-Mesh.
here is a little funny - Crazy Bunny
Thanks a lot on dasch, with your ( and a another decent chap ) tips/tut´s i build this 3D-Mesh.
- Thkoutsidthebox
- Vectric Wizard
- Posts: 1487
- Joined: Wed Oct 25, 2006 3:19 pm
- Location: Europe
- Thkoutsidthebox
- Vectric Wizard
- Posts: 1487
- Joined: Wed Oct 25, 2006 3:19 pm
- Location: Europe
- dasch
- Vectric Apprentice
- Posts: 89
- Joined: Thu Nov 16, 2006 12:16 am
- Location: Vancouver Island
- Contact:
The cat is very cute.
Careful or you'll put me out of work!
Will you be carving these?
Careful or you'll put me out of work!
Will you be carving these?
3D-ish
Dasch's VectorArt3D Models
Dasch's VectorArt3D Models
Hello Dale,dasch wrote:The cat is very cute.
Careful or you'll put me out of work!
Will you be carving these?
no way, you are a professional artist..!! I´m only a hobbyist to check out what i can do
dYes i wish i found a little bit time to carve it, i spend my time all in Silo . it´s a lot of work to learn it..
- Thkoutsidthebox
- Vectric Wizard
- Posts: 1487
- Joined: Wed Oct 25, 2006 3:19 pm
- Location: Europe
cute-kitten
right, i mirrored the half of the cute-kitten, its very simple to do that...Thkoutsidthebox wrote:I like the cat too. Did you create it using the Instance Mirror, or just careful attention to symmetry?
Cheers....
- Thkoutsidthebox
- Vectric Wizard
- Posts: 1487
- Joined: Wed Oct 25, 2006 3:19 pm
- Location: Europe
HA! I'll have to take your word for it. I'm having trouble after creating an object with instance mirror, making the mirrored side a solid part of my object. When I save and open in Cut3D, I only have half of my object there, the mirrored side didn't save as a solid. Want to share your method for this after creation? Thanks in advance!
- dasch
- Vectric Apprentice
- Posts: 89
- Joined: Thu Nov 16, 2006 12:16 am
- Location: Vancouver Island
- Contact:
Which version of Silo are you using?Thkoutsidthebox wrote:HA! I'll have to take your word for it. I'm having trouble after creating an object with instance mirror, making the mirrored side a solid part of my object. When I save and open in Cut3D, I only have half of my object there, the mirrored side didn't save as a solid. Want to share your method for this after creation? Thanks in advance!
If you are in Silo 1.4 you probably just have a 'mirror instance' happening
I can't quite remember, but there should be a 'freeze mirror' menu command somewhere, to make both halves one piece.
3D-ish
Dasch's VectorArt3D Models
Dasch's VectorArt3D Models
mh.. the same problem i had on my first trial with Silo, i fixed this - select all and merge (ctrl+m) it.dasch wrote:Which version of Silo are you using?Thkoutsidthebox wrote:HA! I'll have to take your word for it. I'm having trouble after creating an object with instance mirror, making the mirrored side a solid part of my object. When I save and open in Cut3D, I only have half of my object there, the mirrored side didn't save as a solid. Want to share your method for this after creation? Thanks in advance!
If you are in Silo 1.4 you probably just have a 'mirror instance' happening
I can't quite remember, but there should be a 'freeze mirror' menu command somewhere, to make both halves one piece.
- Thkoutsidthebox
- Vectric Wizard
- Posts: 1487
- Joined: Wed Oct 25, 2006 3:19 pm
- Location: Europe