Turned Box

The Gallery is for posting images of work machined using Cut3D

Turned Box

Postby JMD » Fri Jun 27, 2014 3:49 am

I turned a little round box, but wanted to do something different with the lid.
Attachments
RB Small.jpg
JMD
Vectric Craftsman
 
Posts: 170
Joined: Sun Apr 03, 2011 3:07 pm
Location: Erie, PA
Model of CNC Machine: Shark Pro

Re: Turned Box

Postby mikeacg » Fri Jun 27, 2014 12:12 pm

Looks very nice! What size are we talking here and what bits did you use? I did something like that a few years back with a 1/16" tapered and it scared me half to death...

Mike
User avatar
mikeacg
Vectric Wizard
 
Posts: 610
Joined: Sun Nov 02, 2008 10:53 pm
Location: Newberry, MI
Model of CNC Machine: Camaster Stinger, Sidewinder, SB 4x4

Re: Turned Box

Postby JMD » Fri Jun 27, 2014 2:43 pm

mikeacg wrote:Looks very nice! What size are we talking here and what bits did you use? I did something like that a few years back with a 1/16" tapered and it scared me half to death...

Mike


Thanks Mike. It's about 3" dia and 2 high. Used an 1/8 end mill to rough the top and finished with a 1/16 ball mill. Do not remember the RPM, but was feeding about 40imp.
JMD
Vectric Craftsman
 
Posts: 170
Joined: Sun Apr 03, 2011 3:07 pm
Location: Erie, PA
Model of CNC Machine: Shark Pro

Re: Turned Box

Postby mikeacg » Fri Jun 27, 2014 4:29 pm

Now that I have been doing this for a few years I guess I am less afraid of it but those expensive 1/16" tapered bits are a little daunting. I'm not sure I would ever carve anything that small with enough depth to actually utilize all that cutting edge either. But I have 2 of them 'just in case'! Thanks for sharing!

Mike
User avatar
mikeacg
Vectric Wizard
 
Posts: 610
Joined: Sun Nov 02, 2008 10:53 pm
Location: Newberry, MI
Model of CNC Machine: Camaster Stinger, Sidewinder, SB 4x4

Re: Turned Box

Postby maineshops » Wed Aug 20, 2014 7:47 pm

i've been turning 1.375 pocket watches with a 1.00 carving in them using a .032/,1/32 bit. haven't broken one yet but it is scary to watch. Touching off at the top of the material is iffy. i just use a piece of paper to gauge the surface. i'm running at 20 inches min. i'm going to drop down to a .750 dia carving for ladies pendent watches and see how that goes. Dan up in northern Maine.
maineshops
Vectric Apprentice
 
Posts: 186
Joined: Sat Feb 23, 2013 11:47 pm
Model of CNC Machine: home built

Re: Turned Box

Postby RhoTu » Thu Aug 21, 2014 4:17 pm

maineshops, could you post a photo of one of your watches? What depth do you carve.
RhoTu
Vectric Craftsman
 
Posts: 123
Joined: Mon Dec 29, 2008 10:12 pm

Re: Turned Box

Postby pops1964 » Wed Sep 24, 2014 1:59 pm

Nice box I like it ,good job ,

Would also like to see a picture of maineshops watch . pop's
POPS1964
SHOPBOT Buddy BT-32
pops1964
Vectric Wizard
 
Posts: 322
Joined: Sun Jun 22, 2014 11:09 pm
Location: Michigan USA
Model of CNC Machine: shopbot buddy bt 32


Return to Cut3D - Gallery

Who is online

Users browsing this forum: No registered users and 1 guest