Jesus bust with sweet grain pattern

Gallery for samples created from Design and Make 3D Machinist or using Design & Make projects

Moderator: Todd Bailey

Post Reply
User avatar
Xxray
Vectric Wizard
Posts: 2300
Joined: Thu Feb 17, 2011 8:47 am
Model of CNC Machine: CAMaster Stinger 1
Location: MI USA

Jesus bust with sweet grain pattern

Post by Xxray »

I'm a big fan of poplar, but some is better than others. I saw a 6 ft chuck and home depots last week, and the grain pattern was so amazing that I bought the whole thing.
This is one of the works I have made from it, I really lucked out with the placement on this one. There are lines that feed into the outer corners of both eyes, and another that forms both cheeks. The 3D work really sends the lines meandering, and creates a pretty stunning effect.
1st pic shows rough right off the CNC, 2nd shows it cleaned up and stained. Usually, I would stain the subject and leave the surrounding wood unstained, and apply a clear coat to all.
Did the opposite on this one, as I felt the stain might detract from the grain, so I stained the surrounding wood, and just gave the subject a clear coat.
Attachments
1 (Large).JPG
2 (Large).JPG
Doug

User avatar
esteeme1
Vectric Wizard
Posts: 2132
Joined: Tue Nov 02, 2010 3:26 pm
Model of CNC Machine: Cobra 404 ATC; ROMAX WD-1; Shark
Location: Chesapeake VA
Contact:

Re: Jesus bust with sweet grain pattern

Post by esteeme1 »

There must be some Devine intervention. I don’t think you could plan for that if you tried. The continuity between the grain pattern and the carving is spot on. Great job!
Jim Darlas
"Can Do!"
http://www.esteemedwoodcrafts.com/
http://www.esteemedplaques.com/

User avatar
mezalick
Vectric Wizard
Posts: 2970
Joined: Mon Nov 03, 2008 9:07 am
Model of CNC Machine: Camaster Cobra
Location: Philadelphia, PA USA
Contact:

Re: Jesus bust with sweet grain pattern

Post by mezalick »

Very Nice, The grain looks great.
When it happens, it happens, just sit back and say WOW !
Michael
Michael Mezalick
https://www.youtube.com/user/mezalick
mm@mezalick.com

User avatar
Xxray
Vectric Wizard
Posts: 2300
Joined: Thu Feb 17, 2011 8:47 am
Model of CNC Machine: CAMaster Stinger 1
Location: MI USA

Re: Jesus bust with sweet grain pattern

Post by Xxray »

Very true.
We can do what we can to pick out choice grain and good placement, but where the grain falls, especially in 3D, is almost impossible to accurately predict.
Doug

User avatar
Xxray
Vectric Wizard
Posts: 2300
Joined: Thu Feb 17, 2011 8:47 am
Model of CNC Machine: CAMaster Stinger 1
Location: MI USA

Re: Jesus bust with sweet grain pattern

Post by Xxray »

Don't want to bomb the forum with similar posts.
Nice purpleheart Jesus, first time I have ever worked with it.
Shapes nice, very solid & heavy wood. This piece is 9 x 5.5", and must weigh a couple of pounds. Too bad it loses its purplish ting when shaped.

Usually use matte finish, but went for a gloss coat with this.
Attachments
1 (Large).JPG
Doug

User avatar
esteeme1
Vectric Wizard
Posts: 2132
Joined: Tue Nov 02, 2010 3:26 pm
Model of CNC Machine: Cobra 404 ATC; ROMAX WD-1; Shark
Location: Chesapeake VA
Contact:

Re: Jesus bust with sweet grain pattern

Post by esteeme1 »

Looks great. Much like Cherry the color darkens/richens with age, I think that Purpleheart will do the same.
Jim Darlas
"Can Do!"
http://www.esteemedwoodcrafts.com/
http://www.esteemedplaques.com/

Post Reply